manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

Chapter  4.  Local Memory  

4-1

Chapter 4  
Local Memory

This chapter describes the MCF5272 implementation of the ColdFire Version 2 core local
memory specification. It consists of the following sections.

•

Section 4.3, “SRAM Overview,” and Section 4.4, “ROM Overview,” describe the 
on-chip static RAM (SRAM) and ROM implementations. These chapters cover 
general operations, configuration, and initialization. They also provide information 
and examples showing how to minimize power consumption when using the ROM 
and SRAM. 

•

Section 4.5, “Instruction Cache Overview,” describes the cache implementation, 
including organization, configuration, and coherency. It describes cache operations 
and how the cache interfaces with other memory structures. 

4.1  Interactions between Local Memory Modules

Depending on configuration information, instruction fetches and data read accesses may be
sent simultaneously to the SRAM, ROM, and cache controllers. This approach is required
because the controllers are memory-mapped devices and the hit/miss determination is made
concurrently with the read data access. Power dissipation can be minimized by configuring
the ROM and SRAM base address registers (ROMBAR and RAMBAR) to mask unused
address spaces whenever possible.

If the access address is mapped into the region defined by the SRAM (and this region is not
masked), it provides the data back to the processor and any cache or ROM data is discarded.
If the access address does not hit the SRAM, but is mapped into the region defined by the
ROM (and this region is not masked), the ROM provides the data back to the processor and
any cache data is discarded. Accesses from the SRAM and ROM modules are never cached.
The complete definition of the processor’s local bus priority scheme for read references is
as follows:

if (SRAM “hits”)

SRAM supplies data to the processor
 

if (ROM “hits”)

 

ROM supplies data to the processor

 

else if (cache “hits”)

 

cache supplies data to the processor

          

else system memory reference to access data 

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Garmin GND 10 Installation Instructions preview
GND 10
Brand: Garmin Pages: 2
TC Electronic DB6 User Manual preview
DB6
Brand: TC Electronic Pages: 174
TC Electronic Finalizer Express User Manual preview
Finalizer Express
Brand: TC Electronic Pages: 33
Renesas F-ZTAT H8/3048 Series User Manual preview
F-ZTAT H8/3048 Series
Brand: Renesas Pages: 34
CAP-XX Purpose User Manual preview
Purpose
Brand: CAP-XX Pages: 8
Renesas RL78/G1H User Manual preview
RL78/G1H
Brand: Renesas Pages: 941
Multitech ISI608PC Owner'S Manual preview
ISI608PC
Brand: Multitech Pages: 81
WTI NPS-16HD20-1 User Manual preview
NPS-16HD20-1
Brand: WTI Pages: 178
Grundfos CIM 060 Installation And Operating Instructions Manual preview
CIM 060
Brand: Grundfos Pages: 40
Tektronix 7B87 Instruction Manual preview
7B87
Brand: Tektronix Pages: 143
Xilinx SelectIO 7 Series User Manual preview
SelectIO 7 Series
Brand: Xilinx Pages: 188
Balluff BNI EIP-508 05-Z015 Series User Manual preview
BNI EIP-508 05-Z015 Series
Brand: Balluff Pages: 74
Fujitsu PRIMEPOWER 1500 Manual preview
PRIMEPOWER 1500
Brand: Fujitsu Pages: 21
Fujitsu Power Select D2703-S Short Description preview
Power Select D2703-S
Brand: Fujitsu Pages: 25
Fujitsu PRIMEPOWER 1 Hardware Platform Manual preview
PRIMEPOWER 1
Brand: Fujitsu Pages: 50
Fujitsu PRIMEPOWER 650 Technical White Paper preview
PRIMEPOWER 650
Brand: Fujitsu Pages: 19
Fujitsu PRIMEPOWER 800 Operating Manual preview
PRIMEPOWER 800
Brand: Fujitsu Pages: 86
Fujitsu PRIMEPOWER 800 User Manual preview
PRIMEPOWER 800
Brand: Fujitsu Pages: 145

Brands by name

Popular brands

Load more brands