manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

Chapter  4.  Local Memory  

4-5

ROM Overview

4.3.2.3  Programming RAMBAR for Power Management 

Depending on the configuration defined by RAMBAR, instruction fetch accesses can be
sent to the SRAM module, ROM module, and instruction cache simultaneously. If the
access is mapped to the SRAM module, it sources the read data, discarding the instruction
cache access. If the SRAM is used only for data operands, setting RAMBAR[SC,UC]
lowers power dissipation by disabling the SRAM during all instruction fetches.
Additionally, if the SRAM holds only instructions, setting RAMBAR[SD,UD] reduces
power dissipation.

Consider the examples on Table 4-3 of typical RAMBAR settings:

ROMBAR can be configured similarly, as described in Section 4.4.2.2, “Programming
ROMBAR for Power Management.”

4.4  ROM Overview 

The ROM modules has the following features: 

•

16-Kbyte ROM, organized as 4K x 32 bits

•

Contains data tables for soft HDLC (high-level data link control), DTMF (dual-tone 
multiple frequency) detection, and tone generation. (The ROM does not contain 
instructions.)

•

The ROM contents are not customizeable

•

Single-cycle access

•

Physically located on ColdFire

 

core's high-speed local bus

•

Byte, word, longword address capabilities

•

Programmable memory mapping

4.4.1  ROM Operation

The ROM module contains tabular data that the ColdFire core can access in a single cycle.
The ROM can be located on any 16-Kbyte address boundary in the 4-Gbyte address space.
Section 4.1, “Interactions between Local Memory Modules,” describes priorities when a
fetch address hits multiple local memory resources. 

Table 4-3. Examples of Typical RAMBAR Settings

Data Contained in SRAM

RAMBAR[7–0]

Instructions only

0x2B

Data only

0x35

Both instructions and data

0x21

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

PACOM Professional Series Quick Manual preview
Professional Series
Brand: PACOM Pages: 15
D-Link DFE-690TXD Quick Install Manual preview
DFE-690TXD
Brand: D-Link Pages: 12
u-blox ANT-B10 User Manual preview
ANT-B10
Brand: u-blox Pages: 29
Intel IXP45X Developer'S Manual preview
IXP45X
Brand: Intel Pages: 958
PairGain PG-Flex FLC-704 Manual preview
PG-Flex FLC-704
Brand: PairGain Pages: 20
Dahua NVR41-4KS2 Series User Manual preview
NVR41-4KS2 Series
Brand: Dahua Pages: 452
Raven RFMOW V2 User Manual preview
RFMOW V2
Brand: Raven Pages: 33
UNICORECOMM UM620N User Manual preview
UM620N
Brand: UNICORECOMM Pages: 19
CAME 848EA-0120 Setup And User'S Manual preview
848EA-0120
Brand: CAME Pages: 32
JAKA MiniCab Hardware User Manual preview
MiniCab
Brand: JAKA Pages: 37
Renesas H8S/2646 Series User Manual preview
H8S/2646 Series
Brand: Renesas Pages: 20
M-system M5XSBS Instruction Manual preview
M5XSBS
Brand: M-system Pages: 4
Multitech MTDOT-868 Series Developer'S Manual preview
MTDOT-868 Series
Brand: Multitech Pages: 60
WIN Enterprises PL-83300 User Manual preview
PL-83300
Brand: WIN Enterprises Pages: 25
Honeywell Home LTEM-PA Installation And Setup Manual preview
LTEM-PA
Brand: Honeywell Home Pages: 36
Sennheiser GSP 300 User Manual preview
GSP 300
Brand: Sennheiser Pages: 22
ICOP Technology Vortex86SX VSX-6101 User Manual preview
Vortex86SX VSX-6101
Brand: ICOP Technology Pages: 50
Renesas Direct Dummy IC M3T-DCT42B-450 User Manual preview
Direct Dummy IC M3T-DCT42B-450
Brand: Renesas Pages: 4

Brands by name

Popular brands

Load more brands