manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

About This  Book  

xli

Organization

The USB Specification, Revision 1.1 is a recommended supplement to this chapter. 
It can be downloaded from http://www.usb.org. Chapter 2 of this specification, 
Terms and Abbreviations, provides definitions of many of the words found here.

•

Chapter 13, “Physical Layer Interface Controller (PLIC),” provides detailed 
information about the MCF5272’s physical layer interface controller, a module 
intended to support ISDN applications. The chapter begins with a description of 
operation and a series of related block diagrams starting with a high-level overview. 
Each successive diagram depicts progressively more internal detail. The chapter 
then describes timing generation and the programming model and concludes with 
three application examples.

•

Chapter 14, “Queued Serial Peripheral Interface (QSPI) Module,” provides a 
feature-set overview and description of operation, including details of the QSPI’s 
internal RAM organization. The chapter concludes with the programming model 
and a timing diagram.

•

Chapter 15, “Timer Module,” describes configuration and operation of the four 
general-purpose timer modules, timer 0, 1, 2 and 3. 

•

Chapter 16, “UART Modules,” describes the use of the universal 
asynchronous/synchronous receiver/transmitters (UARTs) implemented on the 
MCF5272, including example register values for typical configurations. 

•

Chapter 17, “General Purpose I/O Module,” describes the operation and 
programming model of the three general purpose I/O (GPIO) ports on the 
MCF5272. The chapter details pin assignment, direction-control, and data registers.

•

Chapter 18, “Pulse Width Modulation (PWM) Module,” describes the configuration 
and operation of the pulse width modulation (PWM) module. It includes a block 
diagram, programming model, and timing diagram. 

•

Chapter 19, “Signal Descriptions,” provides a listing and brief description of all the 
MCF5272 signals. Specifically, it shows which are inputs or outputs, how they are 
multiplexed, and the state of each signal at reset. The first listing is organized by 
function, with signals appearing alphabetically within each functional group. This is 
followed by a second listing sorted by pin number.

•

Chapter 20, “Bus Operation,” describes the functioning of the bus for data-transfer 
operations, error conditions, bus arbitration, and reset operations. It includes 
detailed timing diagrams showing signal interaction. Operation of the bus is defined 
for transfers initiated by the MCF5272 as a bus master. The MCF5272 does not 
support external bus masters. Note that Chapter 9, “SDRAM Controller,” describes 
DRAM cycles.

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Patton electronics 1090 Service Manual preview
1090
Brand: Patton electronics Pages: 8
Tripp Lite N48M Series Installation Manual preview
N48M Series
Brand: Tripp Lite Pages: 20
Paradyne 7995-A2-374 Quick Installation Instructions preview
7995-A2-374
Brand: Paradyne Pages: 1
Belkin F5D9001 Series Manual preview
F5D9001 Series
Brand: Belkin Pages: 72
Analog Devices EZ-Extender Analog 120-Pin Probing Board Manual preview
EZ-Extender Analog 120-Pin Probing Board
Brand: Analog Devices Pages: 29
Orolia Seven Solutions WR-ZEN Series User Manual preview
Seven Solutions WR-ZEN Series
Brand: Orolia Pages: 167
IDT Digital Encoder Plus User Manual preview
Digital Encoder Plus
Brand: IDT Pages: 98
Powerleap PL-PROMMX Manual preview
PL-PROMMX
Brand: Powerleap Pages: 28
IEI Technology PE-6S-R40 User Manual preview
PE-6S-R40
Brand: IEI Technology Pages: 4
Vivint AirBridge VS-YOFIMN-000 Quick Reference preview
AirBridge VS-YOFIMN-000
Brand: Vivint Pages: 2
SilverStone SDP12 Quick Start Manual preview
SDP12
Brand: SilverStone Pages: 2
Allen-Bradley SLC 5/03 Installation Instructions Manual preview
SLC 5/03
Brand: Allen-Bradley Pages: 76
National Instruments PXI-GPIB Getting Started preview
PXI-GPIB
Brand: National Instruments Pages: 45
Inter-m S- Media Manual preview
S- Media
Brand: Inter-m Pages: 20
Rimage CDPR3 User Manual preview
CDPR3
Brand: Rimage Pages: 30
PairGain T1L2F10A Manual preview
T1L2F10A
Brand: PairGain Pages: 76
Arctic Freezer i32 Welcome Manual preview
Freezer i32
Brand: Arctic Pages: 7
Alphacool NexXxoS GPX-N 970 M03 Instruction Manual preview
NexXxoS GPX-N 970 M03
Brand: Alphacool Pages: 2

Brands by name

Popular brands

Load more brands