Mitsubishi FB13PNT, Quick Start Manual

Page: 38 / 292

1-25 1-25
CHAPTER 1 CONTROLLER CHAPTER 1 CONTROLLER
#9 Traveling Power Mode #9 Traveling Power Mode
This setting affec This setting affects the requir ts the required torque ed torque which is calculated which is calculated from acceler from accelerator pedal posit ator pedal position. ion.
The values are s The values are selected from elected from three types: EC three types: ECONOMY, STANDARD ONOMY, STANDARD and HIGH PO and HIGH POWER. WER.
The figure The figure shows the torqu shows the torque characteri e characteristic to the tim stic to the time. e.
500939 500939
T T orque orque
[%] [%]
100 100
Speed –··– Parking brake limit –··– Speed –··– Parking brake limit –··–
(km/h) 0% (km/h) 0%
HIGH POWER(3) HIGH POWER(3)
STANDARD(2) STANDARD(2)
ECONOMY(1) ECONOMY(1)
Service Brake limit* Service Brake limit*
1 1
(50%) (50%)
Thermal, BDI [0] or Service indica Thermal, BDI [0] or Service indica tor* tor*
2 2
0 0 5 5 1 1 5 5 10 10
70 70
85 85
(30%) (30%)
* *
3 3
*1 Service *1 Service
brake limit:
brake limit:
*3 Parking *3 Parking
brake limit:
brake limit:
Torque value r Torque value resulting from esulting from reduction in reduction in
current when the se current when the service brake rvice brake is applied. is applied.
When the parking brake SW is When the parking brake SW is enabled, the enabled, the
torque becomes zero. torque becomes zero.
*2 *2 Th Ther erma mal:l: BD BDI [ I [0] 0] or or Se Serv rvic ice i e ind ndic icat ator or: C : Cur urve ve of of
limited torque under a condition of limited torque under a condition of
overheating or battery voltage low or
overheating or battery voltage low or
maintenance time over.
maintenance time over.
#10 Service Indicator #10 Service Indicator
This setting sets the maintenance time. The time set here is This setting sets the maintenance time. The time set here is
added to the truck's hour meter and that value is stored in added to the truck's hour meter and that value is stored in
memory as the "maintenance time."
memory as the "maintenance time."
When the truck's hour meter reaches maintenance time, the When the truck's hour meter reaches maintenance time, the
service reminder LED turns on.
service reminder LED turns on.
It will flash 20 hours before the time. It will flash 20 hours before the time.
You can reduce the truck power when the LED flashes by You can reduce the truck power when the LED flashes by
setting the service indicator selection. You can also set the
setting the service indicator selection. You can also set the
demo-mode
demo-mode, which shows the , which shows the service Indicator function in a service Indicator function in a
short period of time. short period of time.
The setting value The setting value is as follows. is as follows.
M Ma aiin ntte en na an ncce e ttiim me e [[h ho ou urr]] --
6 min 6 min
(test) (test) 1 10 00 0 1 15 50 0
In increments In increments
of 50 of 50 9 95 50 0 1 10 00 00 0
Set data on Set data on
display
display
IIn nvvaalliid d 0 0
O On nlly y w waarrn niin ng g 0 0..1 1 1 10 00 0 1 15 50 0 ---------- 9 95 50 0 1 10 00 00 0
Torque limit Torque limit =0.1 =0.1 =100 =100 =150 =150 ----- ----- =950 =950 =1000 =1000