Mitsubishi FB13PNT, Quick Start Manual

Page: 75 / 292

1-62 1-62
CHAPTER 1 CONTROLLER CHAPTER 1 CONTROLLER
8 8.. B Ba assiic c C Ch he ecck k
8 8..1 1 T Te essttiin ng g T To oo ollss
8. 8.2 2 Me Meas asur urem emen ent t of of Ca Card rd Vo Volt ltag age e
Always follow basic Always follow basic troubleshooting steps. troubleshooting steps.
-- T Taallk t k to t o th he o e op pe erraatto orr..
-- Confi Confirm rm the o the operat perator's or's descr descriptio iption of n of the the probl problem w em with a ith an ope n operatio rational c nal check heck..
-- Vis Visual ually in ly inspe spect c ct cabl ables, c es, conn onnec ector tors, co s, conta ntacto ctor tip r tips, et s, etc. c.
-- Perf Perform orm basic basic batt battery c ery cables ables to f to frame rame resis resistance tance test test. (at . (at least least 20 k o 20 k ohm) hm)
-- Ch Che eck b ck baatt tte erry co y cond ndit itiion on..
Always check each option and Always check each option and write down the reading. write down the reading.
Note: The Note: The illustrations show digital multimeters. In these illustrations show digital multimeters. In these
multimete multimeters, the positive (+) terminal is rs, the positive (+) terminal is applied with applied with
positive charge, and the negative (-) terminal with positive charge, and the negative (-) terminal with
negative charge. It should be noted that the terminals
negative charge. It should be noted that the terminals
must be connected inversely when using an analog
must be connected inversely when using an analog
meter.
meter.
1. 1. Mul Multim timete eterr
2. 2. Cla Clamp me mp meter ter
3. 3. IC IC cl clip ip
500961 500961
1 1
2 2
3 3
WARNING WARNING
Disconnect the battery plug before in Disconnect the battery plug before inspecting or adjusting the controller. specting or adjusting the controller.
WARNING WARNING
To prevent acc To prevent accidental moveme idental movement of the truc nt of the truck, place wood bloc k, place wood blocks under the ks under the truck to lift the truck to lift the front wheels o front wheels off the ground. ff the ground.
Stay away from the front wheels. Stay away from the front wheels.
(1) (1) Tilt the mast fu Tilt the mast fully backward. Place blo lly backward. Place blocks under the cks under the mast, and tilt the mast, and tilt the mast forward mast forward to raise the fro to raise the front end of the nt end of the truck. truck.
(2) (2) Tur Turn th n the ke e key sw y switc itch of h off. f.
(3) (3) Disco Disconnect t nnect the batt he battery plu ery plug. Rem g. Remove the c ove the cover over..
(4) (4) Rec Reconn onnect t ect the ba he batte ttery pl ry plug. ug.
(5) (5) Turn the key sw Turn the key switch on. Connect itch on. Connect the negative t the negative terminal of the erminal of the multimete multimeter to the V G r to the V GND terminal o ND terminal of the card. f the card.
(6) (6) Set t Set the mu he multim ltimeter eter to th to the 100 e 100 VDC r VDC range ange..
(7) (7) Connect the Connect the positive termin positive terminal of the multim al of the multimeter to eac eter to each pin of connect h pin of connectors detailed on t ors detailed on the following pag he following pages. es.
Note: Be Note: Be careful not to short-circuit pins. For the careful not to short-circuit pins. For the normal voltage value, refer to the card voltage chart on normal voltage value, refer to the card voltage chart on the following pages. the following pages.