manualshive.com logo in svg

Mitsubishi Electric CR750 Series, Instruction Manual

Share
Download
Mitsubishi Electric CR750 Series Instruction Manual Download Page 561

                               

5

Functions set with parameters

   

Interference avoidance function

   6-541

5.24.8 Enabling and disabling the interference avoidance function

Whether to enable/disable the interference avoidance function in general, and whether to enable/disable it 
during program execution and jog operation can be set by setting the parameter: CAV.
Details of the parameter are given in 

Table 5-41

.

Table 5-41:Interference avoidance function enable/disable setting parameter

5.24.9 Using the interference avoidance function

The interference avoidance operation during jog operation and program execution is explained below. Set 
the 1st element of parameter: 

CAV

 to “1” (Enable). (Refer to 

Page 541, "5.24.8 Enabling and disabling the 

interference avoidance function"

.)

(1) Interference avoidance during jog operation

When the 3rd element of parameter: 

CAV

 is set to Enable (“1” or “2”), the interference avoidance function 

can be used during jog operation.
When interference is detected, the robot decelerates to a stop and performs the following operation accord-
ing to the parameter’s setting value.

Setting value = 1: Alarm (L241n) occurs. The alarm must be reset to resume jog operation.
Setting value = 2: A buzzer sounds. The robot can be jogged in the direction where there is no interfer-

ence.

Temporarily canceling the interference avoidance function

Press the [CLEAR] key on T/B to temporary cancel the interference avoidance function for the simu-

lated components. It can be temporarily canceled by setting "0" (temporarily disable) to the second 
element of the simulated component enable/disable setting parameters: 

CAVSCA1 to 8

 (robot arm), 

CAVSCH to 8

 (hand) and 

CAVSCW1 to 8

 (workpiece).

Every time the [CLEAR] key is pressed, the status switches between Enable and Disable. “CAV” is 
displayed at the bottom center of the T/B screen when set to Enable.

If the robot cannot be restarted from an interference state by [CLEAR] key (if the operator manually 

puts the robot into the interference area during servo OFF, etc.), carry out 

Page 61, "3.11 Operation 

to Temporarily Reset an Error that Cannot Be Canceled"

 (jog operation while [RESET] is pressed). 

The interference avoidance function can be temporarily canceled and the robot can be moved.

Note) The robot will not stop at the movement range limit when using this operation. Do not 

move in the direction outside of the movement range.

Parameter

Parameter 

name

No. of arrays

No. of characters

Details explanation

Factory setting

Interference 
avoidance func-
tion

CAV

Integer 1

Set whether to enable or disable the interference 
avoidance function in general.
When set to enable, additionally set to enable/disable 
the interference avoidance function during program 
execution, and  enable (including movement during 
interference)/disable the function during jog operation.

1st element: Use of the interference avoidance function 

(0: Disabled/1: Enabled)

2nd element: Initial state at program execution 

(0: Disabled/1: Enabled)

3rd element: Disable/enable setting for jog operation

(0: Disabled, 1: Enabled with error 
occurrence, 2: Enabled with only buzzer 
sound)

0, 1, 1

<CURRENT>  JOINT   100% P1          B1 
  J1:     0.00       J5:   0.00   

  J2:     0.00       J6:   0.00 

  J3:    90.03         :

  J4:     0.00         :

123

TOOL

XYZ

⇒

CYLNDR

3-XYZ

CAV

Enable = “CAV” displayed
Disable = Blank

Summary of Contents for CR750 Series



























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands