Minolta CF1501 Service Manual Download Page 145

Page: 145 / 270

FrameMaker Ver.5.5E(PC) CF1501/CF2001 DIS/REASSEMBLY, ADJUSTMENT
00.12.25

D-13

(7)

Removal of the Paper Size Detecting Board

(8)

Removal of the LED Board and ATDC Sensors Y, M, and C

NOTE

• Whenever the Imaging Unit has been slid out of the copier, be sure to cover it with the

light blocking bag (black) or light blocking cloth for packing purposes and place it in a
dark place. Avoid leaving it to stand for a long time.

1. Remove the LED Unit.

☞

D-22

✽

Removal of the LED Assy Bk

1. Remove High Voltage Unit 1 and 2.

☞

D-56 (steps 1 through 8)

2. Remove two screws, unplug one connector, and

remove the Paper Size Detecting Board.

4004D184AB

2. Remove two screws and the Right Guide.

4004D108AA

3. Remove two screws and the Right Guide for C.

4004D110AA

4. Remove two screws and the Left Guide.

4004D109AA

Summary of Contents for CF1501















































































































































































































































































Search results

Summary of Contents for CF1501

Reviews:

Brands by name

Popular brands

Minolta CF1501, Service Manual

Search results

Summary of Contents for CF1501

Reviews:

Brands by name

Popular brands