manualshive.com logo in svg

Minolta CF1501, Service Manual

Share
Download
Minolta CF1501 Service Manual Download Page 194

FrameMaker Ver.5.5E(PC)  CF1501/CF2001 DIS/REASSEMBLY, ADJUSTMENT
00.12.25

D-62

(47) Removal of the Charge Neutralizing Relay

(48) Removal of the Waste Toner Full Detecting Sensor

(49) Removal of the Waste Toner Bottle Set Sensor

1. Remove the MSC/PIC Board Box.

☞ 

D-41 (steps 1 through 8)

2. Remove four terminals.
3. Remove one screw and the Charge Neutralizing 

Relay.

4004D160AB

1. Remove the LED Unit.

☞ 

D-22

2. Remove one screw and the Waste Toner Full 

Detecting Sensor Cover.

4004D161AA

3. Unplug one connector and remove the Waste 

Toner Full Detecting Sensor.

4004D162AB

1. Remove the LED Unit.

☞ 

D-22

2. Disengage two locking tabs and remove the 

Waste Toner Bottle Set Sensor Assy.

4004D163AA

Summary of Contents for CF1501















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands