Minolta CF1501 Service Manual Download Page 26

Page: 26 / 270

FrameMaker Ver5.5E(PC) CF1501/CF2001 MECHANICAL/ELECTRICAL
00.12.15

M-11

7-1.

AIDC Detection

• Patterns are produced on the Transfer Belt and AIDC Sensors detect the amount of

toner sticking to the patterns.

1. The light-emitting diode emits infrared rays illuminating the toner pattern on the Trans-

fer Belt.

2. The photoreceiver detects the intensity of the infrared light reflected off the toner pat-

tern on the Transfer Belt.

3. A voltage corresponding to the intensity of the reflected light is output to the PIC Board.

Amount of Toner Sticking

Intensity of Light

Reflected

Output

Large

Low

Small

High

Great

4004M532AA

1136M068AA

Photoreceiver

LED

Power Source

GND

Output

Transfer Belt

Summary of Contents for CF1501















































































































































































































































































Search results

Summary of Contents for CF1501

Reviews:

Brands by name

Popular brands

Minolta CF1501, Service Manual

Search results

Summary of Contents for CF1501

Reviews:

Brands by name

Popular brands