manualshive.com logo in svg

Minolta CF1501, Service Manual

Share
Download
Minolta CF1501 Service Manual Download Page 204

FrameMaker Ver.5.5E(PC)  CF1501/CF2001 DIS/REASSEMBLY, ADJUSTMENT
00.12.25

D-72

(5)

Left Margin

Requirement

This adjustment must be made in any of the following cases:

• The LED Unit has been replaced.
• A paper feed unit has been added.
• The image on the copy deviates in the CD direction.

Adjustment Procedure
1. Call the Tech. Rep. Mode to the screen.
2. Touch these keys in this order: “Machine Adjust” 

→

 “PRT Area” 

→

 “Left Margin.”

3. Load the 1st Drawer with A3 plain paper.
4. Select plain paper on the Paper Type Setting Dial.
5. Select the 1st Drawer.
6. Press the Start key to let the copier produce a test pattern.
7. Check the dimension of width A on the test pattern.

✽

If width A is outside the specified range:

8. Touch “1st” and then change the setting using the Up/Down key.

Adjustment Instructions

If width A is longer than the specifications, make the setting value smaller than the current 
one.
If width A is shorter than the specifications, make the setting value greater than the current 
one.

9. Press the Start key to let the copier produce a test pattern.
10. Check the dimension of width A on the test pattern.
11. If width A is outside the specified range, change the setting again and make a check 

again.

12. If width A falls within the specified range, touch “MENU.”
13. Following the same procedure, adjust for all other paper sources.

Specifications

Adjustment Mode

Setting Range

3.0 

±

 1.0 mm

Left Margin

-3.0 mm to +3.0 mm

Width A on the test pattern produced should fall 
within the following range.

4004D512AA

Width A

Summary of Contents for CF1501















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands