manualshive.com logo in svg

Minolta CF1501, Service Manual

Share
Download
Minolta CF1501 Service Manual Download Page 18

FrameMaker Ver5.5E(PC) CF1501/CF2001 MECHANICAL/ELECTRICAL
00.12.15

M-3

8. Paper Feeding
• Paper is fed from each drawer.

9. Manual Bypass
• Paper is fed from the Manual Bypass Table.

10. 1st Image Transfer
• A DC positive voltage is applied to the backside of the Transfer Belt so that the visible, 

developed image formed on each of the four PC Drums (Y, M, C, and Bk) is transferred 
to the surface of the Transfer Belt.

11. 2nd Image Transfer
• A DC positive voltage is applied to the backside of the paper so that the visible image on 

the surface of the Transfer Belt is transferred to the paper.

12. Paper Separation
• The Transfer Belt Paper Separator Fingers separate the paper properly from the Trans-

fer Belt.

13. Transfer Belt Cleaning
• The residual toner left on the surface of the Transfer Belt is scraped off.

14. Main Erase
• Light from the Main Erase Lamp neutralizes any surface potential remaining on the sur-

face of each PC Drum.

15. PC Drum Cleaning
• The Cleaning Blade scrapes off the residual toner left on the surface of the PC Drum.

16. Fusing
• The Upper and Lower Fusing Rollers apply heat and pressure to the paper so that the 

four different color layers of toner lying on the surface of the paper are mixed and fused 
together, as well as being fixed collectively to the paper.

17. Paper Exit
• Feeds the paper out of the copier onto the Paper Exit Tray.

Summary of Contents for CF1501















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands