manualshive.com logo in svg

Minolta CF1501, Service Manual, Page: 209 / 270

Share
Download
Minolta CF1501 Service Manual Download Page 209

FrameMaker Ver.5.5E(PC)  CF1501/CF2001 DIS/REASSEMBLY, ADJUSTMENT
00.12.25

D-77

18. Fold the test pattern in half lengthwise.
19. Check to see if any of the cyan, magenta, and yellow crosses deviates with reference to 

the black cross.

✽

If any of the crosses deviates:

20. Touch the color of the deviated cross.
21. Change the setting for skew using the Up/Down key.

Setting Instructions

22. Press the Start key to let the copier produce a test pattern.
23. Check to see if any of the cyan, magenta, and yellow crosses deviates with reference to 

the black cross.

24. If any of the crosses deviates, change the setting and make a check again.

4004D521AA

If the cross deviates in the direction of 
A, decrease the setting.
If the cross deviates in the direction of 
B, increase the setting.

Check Position

B

A

Summary of Contents for CF1501















































































































































































































































































Reviews:

No comments