manualshive.com logo in svg

Minolta CF1501, Service Manual

Share
Download
Minolta CF1501 Service Manual Download Page 158

FrameMaker Ver.5.5E(PC)  CF1501/CF2001 DIS/REASSEMBLY, ADJUSTMENT
00.12.25

D-26

(4)

Cleaning of the Original Glass

(5)

Removal of the Original Glass Cooling Fan Motor

(6)

Removal of the Scanner Motor

1. Using a soft cloth dampened with alcohol, wipe 

the Lens clean of dirt.

4004D201AA

1. Remove the IR Rear Upper Cover and IR Rear 

Cover.

2. Unplug one connector and remove the harness 

from one wiring saddle.

3. Remove two screws and the Original Glass Cool-

ing Fan Motor.

4004D018AB

1. Remove the IR Rear Upper Cover, IR Rear 

Cover, and IR Rear Right Cover.

2. Remove the Original Glass Cooling Fan Motor.
3. Remove two screws and the reinforcement 

frame.

4004D015AA

4. Remove four screws and the hinge support in the 

rear of the IR.

4004D027AA

Summary of Contents for CF1501















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands