Minolta CF1501 Service Manual Download Page 131

Page: 131 / 270

FrameMaker Ver.5.5E(PC) CF1501/CF2001 DIS/REASSEMBLY, ADJUSTMENT
00.12.25

(4)

Cleaning of the Paper Dust Remover .............................................. D-39

(5)

Cleaning of the Transfer Belt Unit ................................................... D-39

(6)

Cleaning of the LED ........................................................................ D-40

(7)

Cleaning of the Area around the Waste Toner Collecting Port ........ D-40

(8)

Cleaning of the Fusing Entrance Guide Plate ................................. D-41

(9)

Removal of the Imaging Unit Motor C/M/Y/Bk ................................. D-41

(10) Removal of the Main Motor ............................................................. D-43

(11) Removal of the Ozone Ventilation Fan Motor .................................. D-43
(12) Removal of the Fusing Drive Motor ................................................. D-43

(13) Removal of the Fusing Pressure/Retraction Motor .......................... D-44

(14) Removal of the 1st Image Transfer Pressure/Retraction Motor ...... D-45
(15) Removal of Toner Replenishing Motor C/Bk ................................... D-46

(16) Removal of Toner Replenishing Motor Y/M ..................................... D-46

(17) Removal of the Cleaning Web Drive Motor ..................................... D-46
(18) Removal of the Power Supply Cooling Fan Motor ........................... D-47

(19) Removal of Fusing Cooling Fan Motor 2 ......................................... D-48

(20) Removal of Fusing Cooling Fan Motor 1 ......................................... D-48
(21) Removal of the 2nd Image Transfer Pressure/Retraction Clutch .... D-50

(22) Removal of the Synchronizing Roller Clutch ................................... D-50

(23) Removal of the Manual Feed Paper Take-Up Clutch ...................... D-51
(24) Removal of the Paper Take-Up Clutch ............................................ D-52

(25) Removal of AIDC/Registration Sensor 1/2 ...................................... D-53

(26) Removal of the Temperature/Humidity Sensor ............................... D-54
(27) Removal of the Toner Supply Door Sensor ..................................... D-54

(28) Removal of the Manual Feed Paper Take-Up Sensor ..................... D-54

(29) Removal of the 1st Image Transfer Retraction Position Sensor ...... D-55
(30) Removal of the Double Feed Sensor .............................................. D-55

(31) Removal of the Drawer Set Sensor and Drawer Paper

Near-Empty Sensor ......................................................................... D-56

(32) Removal of the Left Door Switch ..................................................... D-57

(33) Removal of the Right Door Switch ................................................... D-57

(34) Removal of the Front Door Switch ................................................... D-58
(35) Removal of the Fusing Roller Rotation Detecting Sensor ............... D-58

(36) Removal of the Fusing Retraction Position Sensor ......................... D-58

(37) Removal of the Exit Sensor ............................................................. D-58
(38) Removal of the 2nd Image Transfer Pressure Position Sensor ...... D-59

(39) Removal of the Synchronizing Roller Sensor .................................. D-59

(40) Removal of the OHP Detecting Sensor ........................................... D-59
(41) Removal of the CD Paper Size Detecting Sensor Assy .................. D-60

(42) Removal of the Paper Take-Up Roll ................................................ D-60

(43) Removal of the Paper Separator Roll .............................................. D-61
(44) Removal of High Voltage Unit 1 ...................................................... D-61

(45) Removal of High Voltage Unit 2/3 ................................................... D-61

(46) Removal of DC Power Supply 1 ...................................................... D-61
(47) Removal of the Charge Neutralizing Relay ..................................... D-62

(48) Removal of the Waste Toner Full Detecting Sensor ....................... D-62

(49) Removal of the Waste Toner Bottle Set Sensor .............................. D-62

Summary of Contents for CF1501















































































































































































































































































Search results

Summary of Contents for CF1501

Reviews:

Brands by name

Popular brands

Minolta CF1501, Service Manual

Search results

Summary of Contents for CF1501

Reviews:

Brands by name

Popular brands