manualshive.com logo in svg

Minolta CF1501, Service Manual

Share
Download
Minolta CF1501 Service Manual Download Page 109

FrameMaker Ver5.5E(PC) CF1501/CF2001 MECHANICAL/ELECTRICAL
00.12.15

M-94

21-8.

Fusing Temperature Control

• Heater lamps are turned ON and OFF to keep the surface temperatures of the Heating 

Roller and Fusing Roller at predetermined levels.

• The surface temperatures of the Heating Roller and Lower Fusing Roller are detected by 

thermistors that convert temperatures to corresponding electrical signals.

• If the surface temperatures of the Heating Roller and Lower Fusing Roller run inordi-

nately high, power to the heater lamps is shut down.

• The fusing temperature during copy cycles can be fine-adjusted using “Tech. Rep. 

Mode.”

Part Name

Function

Heating Roller 
Heater Lamp 1

• Turns ON during a warm-up cycle.
• Turns ON during a copy cycle (large size CD width 217 mm or 

more)

• Turns ON in the standby state after a warm-up cycle.

Heating Roller 
Heater Lamp 2

• Turns ON during a copy cycle (small size CD width 216 mm or less)
• Set temperatures are the same as those for Heating Roller Heater 

Lamp 1.

Lower Fusing 
Roller Heater 
Lamp

• Turns ON during a warm-up cycle.
• Turns ON during a copy cycle
• 130 °C
• Turns ON in the standby state after a warm-up cycle.

Fusing Thermistor 
1

• Detects the surface temperature of the Heating Roller.
• Temperature control in standby state: 170 °C
• Energy Saver temperature control: 160 °C
• Abnormally high temperature of 220 °C of the Heating Roller 

detected: C0520

Fusing Thermistor 
2

• Detects the surface temperature of the Lower Fusing Roller.
• Temperature control in standby state: 160 °C
• Energy Saver temperature control: 140 °C
• Abnormally high temperature of 190 °C of the Lower Fusing Roller 

detected: C0521

Fusing Thermostat 
1

• Abnormally high temperature of 230 °C of the Heating Roller 

detected: Shuts down power supply to Heating Roller Heater Lamp 
1.

Fusing Thermostat 
2

• Abnormally high temperature of 200 °C of the Lower Fusing Roller 

detected: Shuts down power supply to Lower Fusing Roller Heater 
Lamp.

Set Temperature (°C)

Ambient Temperature

Less than 18 °C

18 °C or more

Plain paper

185

180

OHP

180

180

Thick paper 1

185

185

Thick paper 2

195

195

Summary of Contents for CF1501















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands