manualshive.com logo in svg

Minolta CF1501, Service Manual

Share
Download
Minolta CF1501 Service Manual Download Page 255

FrameMaker Ver5.5E(PC) CF1501/CF2001 SWITCHES ON PWBs/TECH. REP. SETTINGS
00.11.30

S-24

Touch Panel 

Display

Setting (The default is 

 ).

Unit Change

Select who is to replace a unit when its replacement time arrives, 
either “User” or “Service.”
Set the type of “Warning” message displayed on the Touch Panel 
when the replacement time arrives depending on the setting.

Example: Toner
To be replaced by “User”: 
A message that prompts the user to change the Toner Bottle appears.
To be replaced by “Service”: 
A message that tells the user to call the Tech. Rep. appears.

Highlighted

Unit

To be replaced by

Toner

Service

Waste Toner Bottle

User

Service

Fusing Web Unit

User

Service

Oil Coating Unit

User

Service

Fusing Unit

User

Service

Transfer Belt Unit

User

Service

Imaging Unit

User

Service

User

Summary of Contents for CF1501















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands