manualshive.com logo in svg

Minolta CF1501, Service Manual

Share
Download
Minolta CF1501 Service Manual Download Page 256

FrameMaker Ver5.5E(PC) CF1501/CF2001 SWITCHES ON PWBs/TECH. REP. SETTINGS
00.11.30

S-25

(4)

Counter

• Shows the number of copies made on each paper size or type.

<Clearing a Count>
1. Open the counter menu screen.
2. Select the counter to be cleared.
3. Press the Clear key.
       Press the Stop key to undo the clearing operation, restoring the original count.
4. Touch “END”.

Touch Panel 

Display

Setting

Life

Counts the frequency of use of each of the different parts of the 
copier.

✽

: It is not possible to clear the Life counter. It is automatically reset 

when a new unit has been installed.
For “Fusing Web Unit,” however, it is possible to reset the counter 
and enter a count from the 10-Key Pad.

Display

Description

Fusing Unit
Fusing Web Unit
Oil Coating Unit
1st.
2nd.
3rd.
4th.

No. of times a sheet of paper is fed through
No. of times a sheet of paper is fed through
No. of times a sheet of paper is fed through
No. of sheets of paper fed from the 1st Drawer
No. of sheets of paper fed from the 2nd Drawer
No. of sheets of paper fed from the 3rd Drawer
No. of sheets of paper fed from the 4th Drawer

Display

Description

ADF Feed

ADF Rev.

Sorter/Finisher
Staple
Punch
LCC Parts1
LCC Parts2

No. of sheets of paper fed through the ADF take-up 
section
No. of sheets of paper fed through the turnover unit of
the ADF
No. of sheets of paper fed out of the Sorter
No. of stapling sequences performed
No. of holes made
No. of sheets of paper fed from the LCC
No. of sheets of paper fed from the LCC

Display

Description

Cyan IU

Magenta IU

Yellow IU

Black IU

Transfer Belt 
Unit
LPH(C)

LPH(M)

Period of time over which the Cyan Developing Unit 
has been used.
Period of time over which the Magenta Developing 
Unit has been used.
Period of time over which the Yellow Developing Unit 
has been used.
Period of time over which the Black Developing Unit 
has been used.
Period of time over which the Transfer Belt Unit has 
been used.
Period of time over which the Cyan LPH has been 
used.
Period of time over which the Magenta LPH has been 
used.

✽

✽

✽

✽

✽

✽

✽

Summary of Contents for CF1501















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands