manualshive.com logo in svg

Minolta CF1501, Service Manual

Share
Download
Minolta CF1501 Service Manual Download Page 38

FrameMaker Ver5.5E(PC) CF1501/CF2001 MECHANICAL/ELECTRICAL
00.12.15

M-23

9. Image Area Discrimination
• The image areas (color edge area, black edge area, dot area, continuous gradation area) 

are discriminated to optimize edge emphasis, smoothing and other processing just right 
for the image.

• Either edge emphasis or smoothing is selected according to the results of image area 

discrimination.

Original Mode

Original Area

Smoothing/Edge Emphasis

Text & Photo 
mode

Dot area

Smoothing processing

Black edge area

Edge emphasis

Color edge area

Edge emphasis

Continuous gradation area Smoothing processing

Photo Image 
mode

Edge area

Weak edge emphasis

Continuous gradation area

Printed Image 
mode

Dot area

Smoothing processing

Text mode

Dot area

Black edge area

BP amount 100 % (printed 
with Bk toner only)

Color edge area

Edge emphasis

Continuous gradation area

Map mode

Edge area

Strong edge emphasis

Continuous gradation area Smoothing processing

Summary of Contents for CF1501















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands