Minolta CF1501 Service Manual Download Page 245

Page: 245 / 270

FrameMaker Ver5.5E(PC) CF1501/CF2001 SWITCHES ON PWBs/TECH. REP. SETTINGS
00.11.30

S-14

3. Settings in the Administrator Mode

Touch Panel

Display

Setting (The default is

Administrator
Mode

The entry on the “Administrator #” set using the Tech. Rep. mode per-
mits the settings of the following functions.

Administrator
Mode 1/2

Displays the various setting screens including Copy Track and Grada-
tion Adjust.

Copy Track
Functions

Select the number of accounts to be controlled.

Access # Input

From the 10-Key Pad, enter the access number (ID), which can range
0001 to 9999.

Counter Check

Check the counter value for the account.
<Procedure>
1. Place the required number of sheets of A4L or Letter L paper on

the 1st Drawer.

2. Press the Start key to let the copier print the counter list.

Counter Reset

Reset the counter value for the account.
<Procedure>
1. Using the

▼

▲

key, select the account number, for which the

counter is to be reset. Touch “All Accts” to reset the counters of all
accounts.

2. Touch the “Cancel” key.
3. Touch the “YES” key.
4. Touch “OK” to reset the counter.

Permission Level

Select whether to enable (“Permit”) or disable (“Prohibit”) copying
according to the color or black mode for each account.
<Procedure>
1. Using the

▼

▲

key, select the account number for which Per-

mission Level is to be set.

2. Select either Permit or Prohibit copying according to the color or

black mode.

Account Copy
Limit set

Set the maximum number of copies to be made at one time for each
account and copying mode using the 10-Key Pad.

<Procedure>
1. Using the

▼

▲

key, select the account number for which Copy

Limit is to be set.

2. Select either Common or Individual.
3. Select whether to turn ON or OFF Copy Limit and then enter the

maximum number of copies to be made from the 10-Key Pad.

Highlighted

OFF

Account #

Use

▼

▲

key to select the account number, for

which an access number is to be programmed.

Access # Enter a 4-digit access number from the 10-Key Pad.

Common Copy limit is not set for each copying mode.

Individual Copy limit is set for each copying mode.

Summary of Contents for CF1501















































































































































































































































































Search results

Summary of Contents for CF1501

Reviews:

Brands by name

Popular brands

Minolta CF1501, Service Manual

Search results

Summary of Contents for CF1501

Reviews:

Brands by name

Popular brands