Minolta CF1501 Service Manual Download Page 60

Page: 60 / 270

FrameMaker Ver5.5E(PC) CF1501/CF2001 MECHANICAL/ELECTRICAL
00.12.15

M-45

13-3.

Sleeve/Magnet Roller

• The magnet roller having magnetic characteristics and the sleeve roller that rotates on

the magnet roller work together to convey developer to the point of development.

• The magnetic force of the magnet roller is the strongest at the point of development so

that the developer brush stands straight up to deliver the greatest amount of toner to the
PC Drum.

13-4.

Doctor Blade

• The Doctor Blade controls the height of the developer brush, ensuring that the developer

on the Sleeve/Magnet Roller levels out.

4004M008AB

Developer
Brush

Magnet Roller

Sleeve Roller

Magnetic Flux

PC Drum

4004M009AB

Doctor Blade

Sleeve/Magnet Roller

Summary of Contents for CF1501















































































































































































































































































Search results

Summary of Contents for CF1501

Reviews:

Brands by name

Popular brands

Minolta CF1501, Service Manual

Search results

Summary of Contents for CF1501

Reviews:

Brands by name

Popular brands