Minolta CF1501 Service Manual Download Page 188

Page: 188 / 270

FrameMaker Ver.5.5E(PC) CF1501/CF2001 DIS/REASSEMBLY, ADJUSTMENT
00.12.25

D-56

(31) Removal of the Drawer Set Sensor and Drawer Paper Near-Empty Sensor

1. Slide out the drawer.
2. Remove the Rear Upper Cover, Rear Right Cover, Rear Left Cover, and Rear Cover.
3. Remove the MSC/PIC Board Box.

☞

D-41 (steps 1 through 8)

4. Remove four terminals.

✽

Terminal colors: White, blue, red, and orange from
top down

5. Remove two screws and the terminal harness

guide.

4004D138AB

6. Remove two screws and High Voltage Unit 1.
7. Unplug two connectors.
8. Remove the harness from one cord clamp and

one edge cover.

4004D140AB

9. Unplug three connectors.
10. Remove the harness from one edge cover.
11. Remove two screws and High Voltage Unit 1.

4004D139AA

12. Remove one screw and the sensor assy.
13. Remove the harness from one edge cover and

unplug two connectors.

4004D141AB

Summary of Contents for CF1501















































































































































































































































































Search results

Summary of Contents for CF1501

Reviews:

Brands by name

Popular brands

Minolta CF1501, Service Manual

Search results

Summary of Contents for CF1501

Reviews:

Brands by name

Popular brands