manualshive.com logo in svg

Mindray Passport V, Operating Instructions Manual

The Mindray Passport V is an advanced medical device offering cutting-edge features and technology. Gain comprehensive knowledge about its functionalities and maintenance by accessing the Service Manual, available for free download from our website. Enhance your product understanding and ensure efficient usage of this remarkable equipment.

Share
Download
background image

Technical Alarm Messages

Messages

14 - 6

0070- 0-0704-02

Passport V Operating Instructions

14.2.6

IBP Alert Message

14.2.7

CO

2

 Alert Message

14.2.8

GAS Alert Message

ALARM MESSAGE

PRIORITY

REASON

SOLUTION

<IBP Label>: Systolic 
Overrange

3

IBP systolic pressure 
exceeds the 
measurement range.

Ensure that the measured 
pressure label is within the 
measurement range.

<IBP Label>: Diastolic 
Overrange

3

IBP diastolic pressure 
exceeds the 
measurement range.

Ensure that the measured 
pressure label is within the 
measurement range.

<IBP Label>: Mean 
Overrange

3

IBP mean pressure 
exceeds the 
measurement range.

Ensure that the measured 
pressure label is within the 
measurement range.

ALARM MESSAGE

PRIORITY

REASON

SOLUTION

CO

2

: ETCO

2

 Overrange

3

Et CO

2

 outside of 

measurable range

Check patient

CO

2

: InspCO

2

 Overrange

3

Insp CO

2

 outside of 

measureable range

Check patient

CO

2

: Resp Rate 

Overrange

3

The measured RR 
value exceeds the 
measurement range. 

Check Patient.
Check Airway.

ALARM MESSAGE

PRIORITY

REASON

SOLUTION

GM: ETCO

2

 Overrange

3

The measured 
ExpCO

2

 value 

exceeds the 
measurement range. 

Check Patient.
Check Airway.

GM: InspCO

2

 Overrange

3

The measured InsCO

2

 

value exceeds the 
measurement range.

Check Patient.
Check Airway.

GM: Resp Rate 
Overrange

3

The measured RR 
value exceeds the 
measurement range. 

Check Patient.
Check Airway.

GM: Disconnected

2

Appears when the 

Passport V

 

cannot 

detect signals being 
sent by the Gas 
Module.

Ensure Gas Module is turned 
on and interface cable is 
properly connected. If 
problem persists, contact 
Technical Support.

0

Summary of Contents for Passport V

































































































































































































































































































Reviews:

No comments

Related manuals for Passport V

LitterMaid LitterMaid Self-Cleaning Litter Box Quick Start Manual preview
LitterMaid Self-Cleaning Litter Box
Brand: LitterMaid Pages: 2
CDB Goldair PLATINUM GBMR600 Operating Instructions Manual preview
Goldair PLATINUM GBMR600
Brand: CDB Pages: 10
HotDog B107 Instructions For Use preview
B107
Brand: HotDog Pages: 5
Martin System No bark collar User Manual preview
No bark collar
Brand: Martin System Pages: 28
Comper SKC-2S User Manual preview
SKC-2S
Brand: Comper Pages: 24
Bauerfeind LumboLoc Forte ES Instructions For Use preview
LumboLoc Forte ES
Brand: Bauerfeind Pages: 2
Bauerfeind SofTec Lumbo Instructions Manual preview
SofTec Lumbo
Brand: Bauerfeind Pages: 36
Clarisonic skin care brush User Manual preview
skin care brush
Brand: Clarisonic Pages: 8
HoMedics FAC-BR200A-EU2 Manual preview
FAC-BR200A-EU2
Brand: HoMedics Pages: 32
Clinique Sonic System User Manual preview
Sonic System
Brand: Clinique Pages: 14
Garmin KT 15 Quick Start Manual preview
KT 15
Brand: Garmin Pages: 66
Eickemeyer MAGIC 500 User Manual preview
MAGIC 500
Brand: Eickemeyer Pages: 29
Petsafe HIG11-13658 Operating Manual preview
HIG11-13658
Brand: Petsafe Pages: 84
Wildlife Materials International 3850 Manual preview
3850
Brand: Wildlife Materials International Pages: 2
Lanaform LA131010 Manual preview
LA131010
Brand: Lanaform Pages: 20
Lanaform Hydrojet Manual preview
Hydrojet
Brand: Lanaform Pages: 24
Lanaform LA130514 Manual preview
LA130514
Brand: Lanaform Pages: 44
Bemer Veterinary 422100 User Manual preview
Veterinary 422100
Brand: Bemer Pages: 16

Brands by name

Popular brands

Load more brands