Mindray Passport V Operating Instructions Manual Download Page 186 | Manualshive

Page: 186 / 288

background image

Passport V Operating Instructions

0070- 0-0704-02

14 - 9

Messages

Prompt Messages

14.3.3

SpO

2

Prompt Message

Resp: Communication Stop

As the Resp module
communication stops, the data
packets sent by the module can
not be received.

Contact Technical Support.

Resp: High Impedance

Connections not tight and/or
properly secured.
Electrodes dry or loose.
Cable or lead wires damaged.

Ensure proper connection.
(Electrode to lead, lead to
cable, cable to monitor).
Re-prep skin and apply fresh,
moist electrodes.
Check with continuity tester

CHK LEAD

Increased impedance caused by
one of the following:
Chest hair under electrodes.
Dried electrode gel.
Electrode off.
Lead off.
Cracked lead wires.
Poor skin prep.

Prep chest.
Change electrodes.
Replace electrode.
Replace lead.
Replace lead wires.
Clean and abrade skin before
applying electrodes.

ALARM MESSAGE

REASON

SOLUTION

COMMENTS

SpO

2

: No Pulse

No pulse.
Low pulse due to
poor perfusion.
External interference.

Check Patient
Reposition sensor.
Check for source of
external interference.

DPM/Nellcor

SpO

2

: Sensor Fault

Defective sensor

Replace sensor

Masimo/DPM/
Nellcor

SpO

2

: Board Fault

There is a problem
with the SpO

2

measurement board.

Contact Technical
Support.

Masimo

SpO

2

: Initialization Error

No response after
send order during
initialization.

Contact Technical
Support.

Masimo/DPM/
Nellcor

SpO

2

: Communication Error

The monitor and the
SpO

2

modules are

not communicating
properly.

Contact Technical
Support.

Masimo/DPM/
Nellcor

SpO

2

: Communication Stop

As the SpO

2

module

communication
stops, the data
packets sent by the
SpO

2

module can

not be received.

Contact Technical
Support.

Masimo/DPM/
Nellcor

SpO

2

: Low Perfusion

Low pulse amplitude

Check patient
Reposition sensor

Masimo/DPM

SpO

2

: Too Much Light

Ambient light
interfering with
signal

Cover sensor site or
reposition sensor

Masimo

SpO

2

: Unrecognized

Sensor

The sensor is not
recognized by
the Monitor.

Replace the sensor
with a recommended
sensor. Contact
Technical Support

Masimo

«
...
184
185
186
187
188
...
»

Summary of Contents for Passport V

































































































































































































































































































Reviews:

No comments

Related manuals for Passport V

Brand: 4pets Pages: 2

Brand: 4pets Pages: 5

Brand: 4pets Pages: 56

Brand: Magnitone Pages: 27

Vitality Line IL21

Brand: inventum Pages: 16

Brand: Kerbl Pages: 2

Brand: Petsafe Pages: 4

Brand: hydrafacial Pages: 24

Brand: Petwalk Solutions Pages: 88

Brand: Morphy Richards Pages: 2

The Single Shot 900-2840-4

Brand: drybar Pages: 20

Brand: Kittywalk Pages: 4

Go.adventure 5A440

Brand: Streifeneder Pages: 40

Soleoline Soleo Sono

Brand: Zimmer Pages: 62

Brand: Beurer Pages: 52

Brand: Zoovilla Pages: 6

Brand: Zoovilla Pages: 7

Zoovilla TOY0112010800

Brand: Zoovilla Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands