Mindray Passport V Operating Instructions Manual Download Page 199

Page: 199 / 288

Prompt Messages

Messages

14 - 22

0070- 0-0704-02

Passport V Operating Instructions

14.3.15

Alarm Troubleshooting

MESSAGE/PROBLEM

REASON

SOLUTION

High or Low or No Alarm
Sound

Alarm limits not set

Go to

Alarm Setup

and adjust

alarms.

Alarm

Silence All, On

time has

not expired

Press

SILENCE ALL

to reactivate

alarms.

No Arrhythmia
Alarm Sound

Arrhythmia option not installed

Call Sales Rep to purchase
option.

Arrhythmia Alarms off

Go to

Monitor Setup

〉

Advanced Setup

to activate

alarm.

Monitor is in learning mode

Wait until learning is concluded
and monitor patient closely.

Alarms continue to Sound
despite pressing

SILENCE

More than one alarm is active

Press

SILENCE

SILENCE ALL

key to silence.

Check Patient.

No Alarm printout with
Alarm violation

Print on Alarm

is set to

Suspend.

Go to

Print Menu

and set

Print

on Alarm

Active

Summary of Contents for Passport V

































































































































































































































































































Search results

Summary of Contents for Passport V

Reviews:

Related manuals for Passport V

Brands by name

Popular brands

Mindray Passport V, Operating Instructions Manual

Search results

Summary of Contents for Passport V

Reviews:

Related manuals for Passport V

Brands by name

Popular brands