manualshive.com logo in svg

Mindray Passport V, Operating Instructions Manual

The Mindray Passport V is an advanced medical device offering cutting-edge features and technology. Gain comprehensive knowledge about its functionalities and maintenance by accessing the Service Manual, available for free download from our website. Enhance your product understanding and ensure efficient usage of this remarkable equipment.

Share
Download
background image

Passport V Operating Instructions

0070- 0-0704-02

19 - 33

Appendix

Safety Designations

Dielectric Strength

• Complies with the requirements of IEC 60601-1: 1997, clause 20.

• AC power to earth(A-a1): 1500VRMS, 1min/5mA

• AC power to applied part (B-a): 4000VRMS, 1min/5mA

• Applied part to earth(B-d): 1500VRMS, 1min/5mA

• Between applied parts(B-b): 1500VRMS, 1min/5mA

Earthing Impedance

• Complies with the requirements of IEC 60601-1: 1997, clause 18.

• The impedance between the protective earth terminal of the power input connector and 

any tangible metal part (such as screw and equipotential stud) that is protectively earthed 
shall not exceed 0.1 ohms.

Protective Earthing and Potential Equalization

Complies with the requirements of IEC 60601-1: 1997, clause 58.

The protective earth terminal cannot be used for mechanical connections between different 
parts of the equipment or for fixing any component irrelevant to protective or functional 
earthing.

Anti-power Interference

After interference from ESU/defibrillation/electrostatic discharge

The equipment returns to normal operation mode within 10 seconds. The display is able to 
show physiological parameters and waveforms normally. For example, the ECG waveform 
data stored are not lost.

Protection Against Power Failure

Requirements of ISO21647: 2005: provides the device to prevent AC power from 
disconnection and tension of 10 Kg.

If the power supply is restored after interrupted, saved presets, user settings, and patient data 
previous to power failure are retained or can be restored with a DPM storage device. 

The monitor stores up to 96 hours of trend information (approximately 6000 trend items) 
when powered off. The interval for trend data is 1 minute.

Power Input

Complies with the requirements of IEC60601-1: 1997, clause 7.1.

Limitation of Voltage and (or) Energy

Complies with the requirements of IEC60601-1: 1997, clause 1.5.

Defibrillation-proof Applied Part

Complies with the requirements of IEC60601-1: 1997, clause 17.h.

0

Summary of Contents for Passport V

































































































































































































































































































Reviews:

No comments

Related manuals for Passport V

Icare HOME2 Instruction Manual preview
HOME2
Brand: Icare Pages: 48
MALTEC ND-1 Instruction Manual preview
ND-1
Brand: MALTEC Pages: 10
Ovente MFW85 Series Manual preview
MFW85 Series
Brand: Ovente Pages: 12
DogRook DogRook Manual preview
DogRook
Brand: DogRook Pages: 9
BBC Bircher CareMat Ax1T L433 Original Instructions Manual preview
CareMat Ax1T L433
Brand: BBC Bircher Pages: 12
aidapt VA126SB Usage And Maintenance Instructions preview
VA126SB
Brand: aidapt Pages: 8
Braun Silk-epil 7 791 Manual preview
Silk-epil 7 791
Brand: Braun Pages: 10
FreshFace YOUNGLY MEE-ETER User Manual preview
YOUNGLY MEE-ETER
Brand: FreshFace Pages: 4
Copper Fit SOLE RELIEF Instructions For Use preview
SOLE RELIEF
Brand: Copper Fit Pages: 4
SystemRoMedic 70200037 User Manual preview
70200037
Brand: SystemRoMedic Pages: 16
Juvion Juvion SkinXpert User Manual preview
Juvion SkinXpert
Brand: Juvion Pages: 4
AEG LADY BEAUTY SET LBS 5676 Instruction Manual preview
LADY BEAUTY SET LBS 5676
Brand: AEG Pages: 30
AEG MD 5503 Instruction Manual preview
MD 5503
Brand: AEG Pages: 34
AEG MPS 4921 Instruction Manual preview
MPS 4921
Brand: AEG Pages: 56
AEG MPS 4920 Instruction Manual preview
MPS 4920
Brand: AEG Pages: 62
AEG HSM/R 5673 NE Instruction Manual preview
HSM/R 5673 NE
Brand: AEG Pages: 94
AEG PHE 5671 LS Instruction Manual preview
PHE 5671 LS
Brand: AEG Pages: 106
Martin System TT200 User Manual preview
TT200
Brand: Martin System Pages: 64

Brands by name

Popular brands

Load more brands