Mindray Passport V Operating Instructions Manual Download Page 74 | Manualshive

Page: 74 / 288

background image

Passport V Operating Instructions

0070- 0-0704-02

4 - 13

ECG Monitoring

Menus: ECG Main and Submenus

To display the ECG Setup Menu:

1.

On the front panel:
Press the

Normal Screen

key to return to the normal screen.

2.

On the normal screen:
Select

Parameters

〉

ECG

〉

ECG Setup Menu

or
Select the

ECG

tile

〉

ECG Setup Menu

.

3.

To exit, press the

Normal Screen

key on the front panel.

ECG Setup Menu

MENU ITEM

SELECTIONS

COMMENTS

Previous Menu

—

Select to return to previous menu.

Filter

Surgery

Monitor

(default)

ST
Diagnostic

Select to change filter mode for ECG. Diagnostic or ST
must be used for ST analysis.

Channel Bandwidth:
Surgery = 1 to 20 Hz
Monitor = 0.5 to 40 Hz
ST= 0.05 to 40 Hz
Diagnostic = 0.05 to 150 Hz

Note:

If Filter is set to Surgery or Monitor when ST

Analysis is set to On, the ST analysis automatically uses
the ST filter without changing the user-selected filter
setting. If Filter is set to ST or Diagnostic when ST
Analysis is set to On, the ST analysis uses the Filter
setting. The filter displayed in ECG waveform areas is
coincident with the actual filter mode.

HR Source

Auto

(default)

ECG
Art
UA
LV
PA
SpO

2

Select to change heart rate source.

The selections are available if the corresponding
parameters are configured. The selections are in order
of priority from high to low: Auto, ECG, ART, UA, LV,
PA, SpO2.

If Auto is selected, the monitor will switch to the current
highest-priority measuring module, and will display the
actual heart rate source in the numeric tile. If the
module for the selected HR source becomes
unavailable, the monitor will switch to the next
available source.

Pacer Reject

On

Off

(default)

Select to turn pacer reject on (pacer artifact blanked
from display) or off (pacer artifact displayed).

On: Rejects the pacing pulse, and filters the pacing
pulse from the ECG waveforms. The message "Pacer
Reject On" is displayed on the top right of the ECG1
waveform area.
Off: Pacing pulse is not rejected.

Pacer
Enhancement

On

Off

(default)

Select to turn pacer enhancement on or off.

On: If there is pacing pulse, a short, straight vertical
line is used on all ECG waveforms to mark pacing
pulse.
Off: Pacing pulse is not rejected

«
...
72
73
74
75
76
...
»

Summary of Contents for Passport V

































































































































































































































































































Reviews:

No comments

Related manuals for Passport V

Brand: 4pets Pages: 2

Brand: 4pets Pages: 5

Brand: 4pets Pages: 56

ICEROSS POST-OP TF

Brand: Össur Pages: 158

Brand: Dowell Pages: 4

Brand: NU Skin Pages: 12

Brand: BaByliss PRO Pages: 16

Brand: Lloyds Pharmacy Pages: 10

AT3 GENERATION 2

Brand: Pet Gear Pages: 12

Brand: Orbegozo Pages: 20

Brand: Nira Pages: 24

One Pet AI Feeder

Brand: CatLink Pages: 8

Brand: Zoovilla Pages: 6

LED FACIAL MASK

Brand: L(A)B Life + Beauty Pages: 14

Brand: L(A)B Life + Beauty Pages: 15

Brand: Jay Pages: 24

Brand: miseno Pages: 7

Brand: BARK Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands