manualshive.com logo in svg

Mindray Passport V, Operating Instructions Manual

The Mindray Passport V is an advanced medical device offering cutting-edge features and technology. Gain comprehensive knowledge about its functionalities and maintenance by accessing the Service Manual, available for free download from our website. Enhance your product understanding and ensure efficient usage of this remarkable equipment.

Share
Download
background image

Battery Replacement and Maintenance

User Maintenance

17 - 6

0070- 0-0704-02

Passport V Operating Instructions

17.6

Battery Replacement and Maintenance

Battery Replacement

1.

Open battery compartment door, on left side of unit, by pressing the finger grip area 
and sliding the door to the rear.

2.

Slide the release located at the top of the installed battery. This will eject the battery. 
Slide out and remove battery.

3.

Slide in replacement battery until it clicks into place.

4.

Close battery compartment door by sliding the door to the right until it firmly clicks into 
place.

CAUTION:

Replace lithium-ion batteries with part number M05-
010001-06 (Mindray) or 0146-00-0099 ONLY.

NOTE:

Mindray PM batteries (0146-00-0069) may fit inside the 
Passport V monitor but they will not properly report 
charging status.

Battery Maintenance

The batteries may be subject to local regulations regarding disposal. At the end of the 
battery life, dispose of the batteries in accordance with any local regulations. 

NOTE:

Passport V batteries may only be charged within a Passport V 
monitor. Do not attempt to use commercial rechargers.

Lithium-Ion

Storage of the lithium-ion batteries depends on temperature, time period and the degree of 
cell charging state. After 6 months of storage at 23

o

C, fully charged lithium-ion batteries 

have a retention capacity of 93%.

0

Summary of Contents for Passport V

































































































































































































































































































Reviews:

No comments

Related manuals for Passport V

Ossur CTI Instructions For Use Manual preview
CTI
Brand: Ossur Pages: 50
Hagen Fresh & Clear DRINKING FOUNTAIN User Manual preview
Fresh & Clear DRINKING FOUNTAIN
Brand: Hagen Pages: 13
Madeli Slique TRANQUILITY IM-TR2042-00 Specifications, Installation And User’S Manual preview
Slique TRANQUILITY IM-TR2042-00
Brand: Madeli Pages: 24
Delfin SkinFibroMeter User Manual preview
SkinFibroMeter
Brand: Delfin Pages: 19
Jata Beauty SM110B Manual preview
SM110B
Brand: Jata Beauty Pages: 24
SportDOG SPORTTRAINER SD-400E Operating Manual preview
SPORTTRAINER SD-400E
Brand: SportDOG Pages: 116
Radica Games Puppy Tweets T7005 Instruction Manual preview
Puppy Tweets T7005
Brand: Radica Games Pages: 2
Laica NE2007 Instructions And Guarantee preview
NE2007
Brand: Laica Pages: 8
Philips WeightWatchers activelink 2.0 DL8725 Quick Start Manual preview
WeightWatchers activelink 2.0 DL8725
Brand: Philips Pages: 4
Philips Wisp Pediatric Nasal Mask Manual preview
Wisp Pediatric Nasal Mask
Brand: Philips Pages: 38
Vasindux PRO+ User Manual preview
PRO+
Brand: Vasindux Pages: 13
SYSTEMAT BLACK HEADS Manual preview
BLACK HEADS
Brand: SYSTEMAT Pages: 16
PC MARKETING Tropical Series Care, Use And Installation Instructions preview
Tropical Series
Brand: PC MARKETING Pages: 20
PB TEEN Wall Mounted Lighted Up Mirror Assembly Manual preview
Wall Mounted Lighted Up Mirror
Brand: PB TEEN Pages: 2
PawHut D02-021 Assembly & Instruction Manual preview
D02-021
Brand: PawHut Pages: 7
FK Irons Spektra Direkt 2 User Manual preview
Spektra Direkt 2
Brand: FK Irons Pages: 6
Carlton SU 1000 Manual preview
SU 1000
Brand: Carlton Pages: 2
Kurgo G-Train Fitting And Use Instructions preview
G-Train
Brand: Kurgo Pages: 2

Brands by name

Popular brands

Load more brands