manualshive.com logo in svg

Mindray Passport V, Operating Instructions Manual

The Mindray Passport V is an advanced medical device offering cutting-edge features and technology. Gain comprehensive knowledge about its functionalities and maintenance by accessing the Service Manual, available for free download from our website. Enhance your product understanding and ensure efficient usage of this remarkable equipment.

Share
Download
background image

Passport V Operating Instructions

0070- 0-0704-02

16 - 3

Printing

Print Setup Menu

Print on Alarm

If a waveform is initiated by an alarm violation, then the local printer will initiate a 16-second 
or 32-second waveform strip. The print length (16 or 32-seconds) can be set in the Print 
Setup menu. To activate this feature, from the front panel, select 

Alarms: Limits

 

〉

 

Print On 

Alarm

 

〉 

Active

. Then select each parameter for which the feature should be enabled. 

During an alarm printout, the data for the parameter which violated the alarm will be marked 
with an asterisk. The alarm trigger for the printout is indicated on the strip with the name of 
the violated alarm.

Interval Printing

To print waveform strips at regular intervals, go to the 

Print Setup Menu, 

highlight 

Print 

Interval

 and select a time interval to print. The selections are 

Off, 1 min, 5 min, 10 

min, 15 min, 20 min, 30 min, 1 hr

 and

 2 hr

. The source of the printout is indicated on 

the strip as 

AUTO REALTIME REPORT

.

Trend Printing

To print 

Quick Trend

, 

List Trend

,

 OxyCRG, 

or 

Graphic Trend

 data to the local printer, 

press the 

Print Trend 

key while the trend is displayed. To abort printing, press the 

Cont 

ECG

, 

Strip

, or 

Print Trend

 key.

Quick Trend and List Trend print digital data information while Graphic Trend print graphic 
representations of the data in the respective menus. Quick Trend entries are only recorded 
upon NIBP readings.

FIGURE 16-2

Graphic Trend Format

FIGURE 16-3

List Trend Format

0

Summary of Contents for Passport V

































































































































































































































































































Reviews:

No comments

Related manuals for Passport V

Darco SlimLine Quick Start Manual preview
SlimLine
Brand: Darco Pages: 2
i-SENS KetoSens Manual preview
KetoSens
Brand: i-SENS Pages: 28
i-SENS VetMate User Manual preview
VetMate
Brand: i-SENS Pages: 52
Össur Front Closure Clavicle Support Instructions For Use preview
Front Closure Clavicle Support
Brand: Össur Pages: 2
Barkmate 113R Manual preview
113R
Brand: Barkmate Pages: 2
SPORT ELEC C2212 Quick Start Manual preview
C2212
Brand: SPORT ELEC Pages: 5
Rowen RESET & BOOST SKIN DUO Quick Start Manual preview
RESET & BOOST SKIN DUO
Brand: Rowen Pages: 4
Hitachi MXS2ESLL1 Probe Instruction Manual preview
MXS2ESLL1 Probe
Brand: Hitachi Pages: 24
Hitachi NC-5510 Instructions Manual preview
NC-5510
Brand: Hitachi Pages: 20
Hitachi HadaCrie CM-N58000BF Instructions Manual preview
HadaCrie CM-N58000BF
Brand: Hitachi Pages: 39
Hitachi CM-N8100 Instructions For Use Manual preview
CM-N8100
Brand: Hitachi Pages: 30
Hitachi CM-N28000BF Instructions Manual preview
CM-N28000BF
Brand: Hitachi Pages: 35
Motorola WIRELESSFENCE25 User Manual preview
WIRELESSFENCE25
Brand: Motorola Pages: 44
Motorola SMARTCOLLAR5000 User Manual preview
SMARTCOLLAR5000
Brand: Motorola Pages: 27
Motorola TRAINER200U User Manual preview
TRAINER200U
Brand: Motorola Pages: 27
Motorola TRAVELFENCE50 User Manual preview
TRAVELFENCE50
Brand: Motorola Pages: 50
Motorola SCOUTTRAINER25 User Manual preview
SCOUTTRAINER25
Brand: Motorola Pages: 44
Tri-Tronics Field G3 series Owner'S Manual preview
Field G3 series
Brand: Tri-Tronics Pages: 26

Brands by name

Popular brands

Load more brands