Mindray Passport V Operating Instructions Manual Download Page 108

Page: 108 / 288

Passport V Operating Instructions

0070- 0-0704-02

6 - 5

SpO2 Monitoring

SpO

Pulse Oximetry

6.4

SpO

Pulse Oximetry

Pulse oximetry is a continuous and non-invasive measurement of the amount of oxygen
attached to the hemoglobin in red blood cells. SpO

is an estimation of arterial oxygen

saturation, SpO

may be used interchangeably with SaO

. The

Passport V

comes

standard with Masimo SET

SpO

. Nellcor

OxiMax

SpO

and DPM SpO

are options.

SpO

Measurements

Select the appropriate sensor for the patient.

Attach the SpO

patient cable to the sensor and plug the other end of the patient cable

into the SpO

connector located on the left side panel of the monitor.

NOTE:

Do not place the sensor on an extremity with an IV catheter
or blood pressure cuff in place.

The pleth waveform and digital SpO

value will be displayed by default in the second

waveform and parameter area. If desired, enter the

Display Setup Menu

to position

Pleth waveform and data in an alternate location.

Calibration

The oximetry sub-system incorporates automatic calibration mechanisms. No other
calibration is required.

Auto Scaling

The pleth waveform is automatically scaled and is not proportional to the patient’s pulse
volume. There is no adjustment that can be made to the pleth waveform.

CAUTION:

Tissue damage or inaccurate measurements may be caused
by incorrect SpO2 sensor application or use, such as
wrapping too tightly, applying supplemental tape, failing to
inspect the sensor site periodically, or failing to position
appropriately. Carefully read the sensor directions for use,
the Passport V Operating Instructions, and all precautionary
information before use.

CAUTION:

Inaccurate SpO2 measurements may be caused by:

•

Incorrect sensor application or use

•

Significant levels of dysfunctional hemoglobins, (e.g.,
carboxyhemoglobin or methemoglobin)

•

Intra-vascular dyes such as indocyanine green or
methylene blue

•

Exposure to excessive illumination such as surgical
lamps (especially ones with a xenon light source),
bilirubin lamps, fluorescent lights, infrared heating
lamps, or excessive ambient light. In such cases, cover
the sensor site with opaque material

•

Excessive patient movement

•

Venous pulsations

•

Electro-surgical interference

Summary of Contents for Passport V

































































































































































































































































































Search results

Summary of Contents for Passport V

Reviews:

Related manuals for Passport V

Brands by name

Popular brands

Mindray Passport V, Operating Instructions Manual

Search results

Summary of Contents for Passport V

Reviews:

Related manuals for Passport V

Brands by name

Popular brands