Mindray Passport V Operating Instructions Manual Download Page 176

Page: 176 / 288

Passport V Operating Instructions

0070- 0-0704-02

13 - 9

Alarms

Alarms also can be verified by creating an alarm condition on the

Passport V

and

verifying the corresponding alarm indicators are present on the monitor.

Alarm Delay

• Apnea Alarm Delay settings are: Adult/Pedatric: 10/15/20/25/30/35/40/45/50/

55 seconds, 1 min
Neonate: 10/15/20 sec

• ST Alarm Delay settings are:

30 seconds/45 seconds/ 1 min/90 seconds/2 min/3 min.

• Alarm delay settings are:

None/1s/2s/3s/4s/5s/6s/7s/8s.

Audio alarm can be delayed for a predetermined time period, with the exception of Apnea,
ST alarm, lethal Arrhythmia alarms, SpO

Desat and Insp O

shortage.

When alarm is triggered, the alarm tone will not be presented, but the visual signal will be
presented during delay time.

13.1.6

Alarm Troubleshooting

MESSAGE/PROBLEM

REASON

SOLUTION

High or Low or No Alarm
Sound

Alarm limits not set

Go to

Alarm Setup

and adjust

alarms

Alarm

Silence All, On

time has

not expired

Press

SILENCE ALL

to reactivate

alarms

No Arrhythmia
Alarm Sound

Arrhythmia option not installed

Call Sales Rep to purchase option

Arrhythmia Alarms off

Go to

Monitor Setup

〉

Advanced Setup

to activate

alarm

Monitor is in learning mode

Wait until learning is concluded
and monitor patient closely

Alarms continue to Sound
despite pressing

SILENCE

More than one alarm is active

Press

SILENCE

SILENCE ALL

key to silence

Check Patient

No Alarm printout with
Alarm violation

Print on Alarm

is set to

Suspend

Go to

Print Menu

and set

Print

on Alarm

Active

Summary of Contents for Passport V

































































































































































































































































































Search results

Summary of Contents for Passport V

Reviews:

Related manuals for Passport V

Brands by name

Popular brands

Mindray Passport V, Operating Instructions Manual

Search results

Summary of Contents for Passport V

Reviews:

Related manuals for Passport V

Brands by name

Popular brands