Metrodata FCM9002 User Manual Download Page 44

Page: 44 / 145

FCM9002 USER MANUAL

76-02-095 Rev.B

Page 44 of 145

4.1.10.1 System Event Log

The system event log gives the time of system level events such as system
restarts, or NTP updates.

Metrodata FCM9002 “FCM9002”

Alarms: Major

--- System Event Log ---

12/11/2012 10:37:22

clock set via NTP

12/11/2012 09:26:05

NTP failed

12/11/2012 09:23:00

performance log cleared

12/11/2012 09:23:00

rtc needs to be set

12/11/2012 09:23:00

config restored

12/11/2012 09:23:00

event logs cleared

press any key to continue

4.1.10.2 Alarm Event Log

The Alarm event log lists the time of all alarm events including start and finish
time.

Metrodata FCM9002 “FCM9002”

Alarms: Major

--- Alarm Event Log ---

12/11/2012 09:26:45

Minor OFF Flow2

12/11/2012 09:26:45

Minor OFF Flow1

12/11/2012 09:26:45

Major OFF LAN1

12/11/2012 09:23:38

Major ON LAN1

12/11/2012 09:23:35

Minor ON Flow2

12/11/2012 09:23:35

Minor ON Flow1

press any key to continue

Summary of Contents for FCM9002


















































































































































Search results

Summary of Contents for FCM9002

Reviews:

Related manuals for FCM9002

Brands by name

Popular brands

Metrodata FCM9002, User Manual

Search results

Summary of Contents for FCM9002

Reviews:

Related manuals for FCM9002

Brands by name

Popular brands