Metrodata FCM9002 User Manual Download Page 26

Page: 26 / 145

FCM9002 USER MANUAL

76-02-095 Rev.B

Page 26 of 145

2.3.4 Unit Status (OK) LED

The OK LED is a bicolour LED with the following states

OFF

Unit not powered up

RED ON

The selected WAN port has alarms

RED FLASH

Both the selected WAN and User Ports have alarms

GREEN FLASH

The User ports have alarms

GREEN ON

No Alarms present.

The OK LED, gives an indication of the status of the device, and if it is not
displaying GREEN ON, ie normal operation, the user should view the Global
Status Screen on the user interface to determine the current alarm state.

It is advisable to change the state of unused ports to down as this will prevent
them from generating alarms which will show on the OK LED.

Summary of Contents for FCM9002


















































































































































Search results

Summary of Contents for FCM9002

Reviews:

Related manuals for FCM9002

Brands by name

Popular brands

Metrodata FCM9002, User Manual

Search results

Summary of Contents for FCM9002

Reviews:

Related manuals for FCM9002

Brands by name

Popular brands