Metrodata FCM9002 User Manual Download Page 32

Page: 32 / 145

FCM9002 USER MANUAL

76-02-095 Rev.B

Page 32 of 145

3.2.2 Pushing S-Tag onto Tagged Frame

When a tagged frame ingresses a user port in Stag mode it will have an Stag
pushed as shown below:

Where

9100

S-Tag Ethertype

PRI

Priority

Stag ID in range 1 to 4095

When the pushed Stag is constructed it gains the Ethertype from the configured
value. The default value is 9100, and setting this to 8100 will give QinQ
operation, effectively VLAN within VLAN encapsulation.

The priority for an tagged frame may either be set to the default port priority, or
be set to inherit a value based on the incoming C-Tag priority.

The ID is the value defined for the flow assigned to the port.

Summary of Contents for FCM9002


















































































































































Search results

Summary of Contents for FCM9002

Reviews:

Related manuals for FCM9002

Brands by name

Popular brands

Metrodata FCM9002, User Manual

Search results

Summary of Contents for FCM9002

Reviews:

Related manuals for FCM9002

Brands by name

Popular brands