Mercury 3.0L Carbureted Alpha Installation Manual Download Page 91

Page: 91 / 137

GASOLINE STERNDRIVE INSTALLATION MANUAL

90-860172011

Page 91 of 137

5. Lightly pull on remote control shift cable end guide (to remove slack from remote control

and cable) and adjust brass barrel as necessary to align attaching points with shift lever
clevis pin hole and stud. Be sure to maintain light pressure on drive unit shift cable.

50309

a -

End Guide

b -

Brass Barrel

c -

Shift Lever Clevis Pin Hole

d -

Stud

6. Temporarily install remote control shift cable on stud and install clevis pin.

50308

a -

Remote Control Shift Cable

b -

Clevis Pin

7. Shift remote control as stated in a. or b. following:

a. Right Hand (RH) Rotation Drive Unit - REVERSE gear, past detent, into WOT

position.

b. Left Hand (LH) Rotation Drive Unit - FORWARD gear, past detent, into WOT

position.

(RH)

(LH)

Summary of Contents for 3.0L Carbureted Alpha










































































































































Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands

Mercury 3.0L Carbureted Alpha, Installation Manual

Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands