Mercury 3.0L Carbureted Alpha Installation Manual Download Page 100

Page: 100 / 137

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 100 of 137

90-860172011

Trim Position Sender Adjustment

ANALOG GAUGES

1. Loosen both trim position sender retaining screws.

71220

a -

Retaining Screws

b -

Trim Position Sender

CAUTION

DO NOT start engine in the following step or damage to sterndrive unit and engine
could result from lack of cooling water.

2. Turn ignition key to RUN position.

3. Trim sterndrive unit to the full DOWN/IN position.

4. Rotate trim position sender as required to show full DOWN/IN position on dashboard

instrument as shown.

71671

a -

Trim Gauge Needle

5. Tighten retaining screws and turn ignition key to the OFF position.

71220

a -

Retaining Screws

b -

Trim Position Sender

Summary of Contents for 3.0L Carbureted Alpha










































































































































Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Brands by name

Popular brands

Mercury 3.0L Carbureted Alpha, Installation Manual

Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Brands by name

Popular brands