Mercury 3.0L Carbureted Alpha Installation Manual Download Page 80

Page: 80 / 137

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 80 of 137

90-860172011

IMPORTANT: Shift slide assembly is free to rotate on core wire. Ensure that shift slide
remains in upright position and is properly engaged with shift shaft lever roller while
installing drive unit.

2. Engage shift shaft roller into shift shaft lever. Snap the Shift Shaft Slide Stabilizer Tool

onto stud directly below shift slide and position as shown.

50629

75198

75199

a -

Shift Shaft Lever

b -

Roller

c -

Shift Shaft Slide Stabilizer Tool

Description

Part Number

Shift Shaft Slide Stabilizer Tool

91-809815A1

3. Position drive unit shift shaft so that it is straight forward by turning shift shaft

CLOCKWISE while simultaneously turning propeller shaft COUNTERCLOCKWISE.

75512

a -

Drive Unit Shift Shaft

Summary of Contents for 3.0L Carbureted Alpha










































































































































Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands

Mercury 3.0L Carbureted Alpha, Installation Manual

Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands