manualshive.com logo in svg

Mercury 3.0L Carbureted Alpha, Installation Manual

Share
Download
Mercury 3.0L Carbureted Alpha Installation Manual Download Page 102

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 102 of 137

90-860172011

ENGINE REV-LIMITER

IMPORTANT: The engines listed in the following chart are equipped with a rpm
rev-limiter that is set to an upper (or limited) rpm amount. This limit is slightly above
the normal operating range of the engine and is designed to help prevent damage
from excessive engine rpm. When the engine reaches the rev-limit rpm, the horn will
sound. Once the rpm drop into the recommended operating rpm range, normal
engine operation resumes.

Engine Rev-Limiter

Model

Engine Recommended Operating

RPM Range

Rev-Limit RPM Setting

3.0L

4400-4800

Not Applicable

4.3L

4400-4800

4950

5.0L

4400-4800

4950

5.7L

4400-4800

4950

Propeller Installation

WARNING

Be sure that remote control is in NEUTRAL position and ignition key is removed
from switch prior to installing propeller.

WARNING

Place a block of wood between the anti-ventilation plate and propeller to protect
hands from propeller blades and to prevent propeller from turning when tightening
propeller nut.

71560

Summary of Contents for 3.0L Carbureted Alpha










































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands