manualshive.com logo in svg

Mercury 3.0L Carbureted Alpha, Installation Manual

Share
Download
Mercury 3.0L Carbureted Alpha Installation Manual Download Page 68

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 68 of 137

90-860172011

IMPORTANT: If boat is being equipped with a REMOTE CONTROL THAT HAS
SEPARATE SHIFT AND THROTTLE LEVERS, the shift assist assembly that is shipped
with the engine should NOT be used. The use of the shift assist assembly with this
type of remote control can cause the shift lever to move out of gear unexpectedly.

The following kit will have to be ordered to connect remote control shift cable when shift
assist assembly is not used.

Spacer Kit

23-11284A1

50310

d

a

c

b

a -

Clevis Pin

b -

Washer

c -

Spacer

d -

Cotter Pin

NOTE: Do not discard shift assist assembly until after it is used in step 3., following.

IMPORTANT: Shift cable must be connected at the remote control for the appropriate
rotation (LH or RH) drive unit, as explained following:

RIGHT HAND ROTATION - Control cable will have to be installed in remote control so that
cable end will move in direction “

A

” when shift handle is placed in the FORWARD position.

LEFT HAND ROTATION - Control cable will have to be installed in remote control so that
cable end will move in direction “

B

” when shift handle is placed in the FORWARD position.

71656

A

B

Summary of Contents for 3.0L Carbureted Alpha










































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands