manualshive.com logo in svg

Mercury 3.0L Carbureted Alpha, Installation Manual

Share
Download
Mercury 3.0L Carbureted Alpha Installation Manual Download Page 94

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 94 of 137

90-860172011

IMPORTANT: If an extra long remote control shift cable is used, there are a large
number of bends in remote control shift cable or remote control has inadequate
output travel, an additional adjustment may be necessary. Refer to step 12. or 13. as
applicable.

12. Remote Control with Single Lever Shift/Throttle Control:

a. RIGHT HAND (RH) propeller rotation drive unit - Shift remote control into

REVERSE gear, WOT position while simultaneously rotating propeller shaft
CLOCKWISE. Clutch should engage and cause propeller shaft to lock. If clutch does
not engage, loosen adjustable stud on shift lever and move it up in slot until clutch
engages with REVERSE gear. Retighten stud. Shift remote control several times
and stop in REVERSE to recheck shift cutout switch position. Pin must be centered.

b. LEFT HAND (LH) propeller rotation drive unit - Shift remote control into

FORWARD gear, WOT position while simultaneously rotating propeller shaft
CLOCKWISE. Clutch should engage and cause propeller shaft to lock. If clutch does
not engage, loosen adjustable stud on shift lever and move it up in slot until clutch
engages with FORWARD gear. Retighten stud. Shift remote control several times
and stop in FORWARD to recheck shift cutout switch position. Pin must be centered.

13. Two Lever Remote Control with Separate Shift and Throttle Levers:

a. RIGHT HAND (RH) propeller rotation drive unit - While turning propeller shaft

CLOCKWISE, move remote control shift handle into full REVERSE position. Clutch
should engage before shift lever comes to a stop. If clutch does not engage, loosen
adjustable stud on shift lever and move it up in slot until clutch engages with
REVERSE gear. Retighten stud. Shift remote control several times and stop in
REVERSE to recheck shift cutout switch position. Pin must be centered.

b. LEFT HAND (LH) propeller rotation drive unit - While turning propeller shaft

CLOCKWISE, move remote control shift handle into full FORWARD position. Clutch
should engage before shift lever comes to a stop. If clutch does not engage, loosen
adjustable stud on shift lever and move it up in slot until clutch engages with
FORWARD gear. Retighten stud. Shift remote control several times and stop in
FORWARD to recheck shift cutout switch position. Pin must be centered.

50309

75435

a

b

a -

Adjustable Stud

b -

Shift Cutout Switch Plunger Pin

Summary of Contents for 3.0L Carbureted Alpha










































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands