Mercury 3.0L Carbureted Alpha Installation Manual Download Page 19 | Manualshive

Page: 19 / 137

background image

GASOLINE STERNDRIVE INSTALLATION MANUAL

90-860172011

Page 19 of 137

Fuel Inlet Fitting

IMPORTANT: The following information is provided to ensure proper installation of
brass fittings or plugs installed into fuel pump or fuel filter base:

•

Use #592 Loctite Pipe Sealant with Teflon on threads of fuel inlet fittings or plugs.
DO NOT USE TEFLON TAPE.

•

Fuel inlet fittings or plugs should first be threaded into fuel pump or fuel filter
base until finger tight.

•

Fuel inlet fittings or plugs should then be tightened an additional 1-3/4 to 2-1/4
turns using a wrench. DO NOT OVERTIGHTEN.

•

To prevent over-tightening when installing a fuel line, the brass fittings should be
held with a suitable wrench as fuel inlet fittings are tightened securely.

WARNING

Boating standards (NMMA, ABYC and others) and Coast Guard regulations must
be adhered to when installing fuel delivery system.

WARNING

Avoid gasoline fire or explosion. Improper installation of brass fittings or plugs into
fuel pump or fuel filter base can crack casting and/or cause a fuel leak.

1. Remove plastic plug from fuel inlet hole.

2. Apply sealant to threads of fuel inlet fitting. DO NOT USE TEFLON TAPE.

3. Install fuel inlet fitting. To prevent cracking the casting or causing fuel leaks, turn fuel inlet

fitting in by hand until finger tight, then tighten connector to 1-3/4 to 2-1/4 turns with
wrench. DO NOT overtighten.

77108

a

A

78165

b

A

a

3.0L Model

Typical V6 And V8 Models

a -

Fuel Inlet Hose Connects Here

b -

Fuel Outlet

Description

Where Used

Part Number

A

Loctite 592

Fuel Inlet Fitting

Obtain Locally

«
...
17
18
19
20
21
...
»

Summary of Contents for 3.0L Carbureted Alpha










































































































































Reviews:

No comments

Related manuals for 3.0L Carbureted Alpha

Brand: SAESHIN Pages: 2

Brand: phytron Pages: 29

Confidant ZT710

Brand: Kohler Pages: 24

Brand: KONTRONIK Pages: 6

Brand: Simple Motors Pages: 6

Brand: STEPCRAFT Pages: 24

Brand: Baumr-AG Pages: 25

Brand: Yanmar Pages: 76

Brand: Yanmar Pages: 234

116-BOXER IRS - V1.7

Brand: MVVS Pages: 6

G18 LT20 Series

Brand: Wood-mizer Pages: 22

Brand: Torini Pages: 16

ZA top SM160.30B/S

Brand: ZIEHL-ABEGG Pages: 72

Brand: rojaflex Pages: 20

Brand: TRAXX Pages: 8

Brand: Mitsubishi Pages: 30

Brand: Mitsubishi Pages: 31

Brand: 3W Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands