manualshive.com logo in svg

Mercury 3.0L Carbureted Alpha, Installation Manual

Share
Download
Mercury 3.0L Carbureted Alpha Installation Manual Download Page 120

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 120 of 137

90-860172011

3. Repeatedly clean out drain holes using a stiff piece of wire. Do this until entire system

is drained.

NOTE: It may be necessary to lift or bend hoses to allow water to drain completely.

4. Models equipped with circulating pump hose drain plug: Remove drain plug.

5. Models without circulating pump hose drain plug: Loosen hose clamps and discon-

nect hose from thermostat housing or circulating pump. Allow water to drain.

74774

a

b

a -

Thermostat Housing To Circulating Pump Hose

b -

Drain Plug Location, If Equipped

6. Make sure gear housing water vent and drain holes, speedometer pitot hole and trim

tab cavity vent and drain holes are open and unobstructed.

71216

a

b

c

d

a -

Vent Holes

b -

Trim Tab Cavity Drain Holes

c -

Drain Hole

d -

Speedometer Pitot Hole

7. Crank engine over slightly with starter motor to purge any water trapped in seawater

pickup pump. Do not allow engine to start.

8. After cooling system has been drained completely, install drain plugs, reconnect hoses

and tighten all hose clamps securely.

Summary of Contents for 3.0L Carbureted Alpha










































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands