Mercury 3.0L Carbureted Alpha Installation Manual Download Page 13

Page: 13 / 137

GASOLINE STERNDRIVE INSTALLATION MANUAL

90-860172011

Page 13 of 137

TAPE MEASURE METHOD

1. Determine X-Dimension from the following chart.

Transom Angle

(degrees)

This dimension should only be raised or lowered after proper

testing.

14-5/16 in. (364 mm)

14-1/4 in. (362 mm)

14-3/16 in. (360 mm)

14-1/8 in. (359 mm)

14-1/16 in. (357 mm)

14 in. (356 mm)

13-15/16 in. (354 mm)

2. Measure up from the boat bottom the amount shown on the chart for the appropriate

transom angle.

71622

71623

Single Engine

Dual Engine

3. Draw a line perpendicular to vertical centerline at crankshaft horizontal centerline.

Summary of Contents for 3.0L Carbureted Alpha










































































































































Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands

Mercury 3.0L Carbureted Alpha, Installation Manual

Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands