manualshive.com logo in svg

Mercury 3.0L Carbureted Alpha, Installation Manual

Share
Download
Mercury 3.0L Carbureted Alpha Installation Manual Download Page 58

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 58 of 137

90-860172011

Audio Warning System Connections

WARNING

Alarm is not external ignition-proof, therefore, DO NOT mount alarm in engine or
fuel tank compartments.

1. Select a location for audio warning alarm which meets all of the following:

•

alarm can be easily heard, yet is out of sight

•

alarm can be easily accessed for installation and maintenance

•

alarm will remain dry

•

alarm is within length limits of the 18 in. purple alarm wire that connects to the “I” terminal
or 12 volt source on switched side of ignition switch.

NOTE: The terminal to which wire is attached must have no voltage when ignition switch
is in the OFF position.

2. Place alarm in desired location and secure to wire bundle with tie-strap provided.

3. Connect PURPLE wire from alarm to any PURPLE wire terminal on instrument gauge

or ignition switch. Tighten connection securely.

4. Connect TAN/BLUE wire from alarm to TAN/ BLUE wire from instrument harness.

5. Place the small (transparent) decals on the bottom of the water temperature and the oil

pressure gauges.

6. Place the large decal on the instrument panel or other appropriate location in easily

viewed by the operator.

75430

ALARM INDICATES LOW

OIL OR OVERHEATING

APPLY THE PROPER DECAL TO THE DASHBOARD

OR OTHER APPROPRIATE LOCATION:

AUDIO WARNING HORN WILL SOUND WHEN:

1. ENGINE OIL PRESSURE IS TOO LOW
2. ENGINE TEMP. IS TOO HIGH, OR
3. DRIVE OIL LEVEL IS TOO LOW 

TO TEST AUDIO WARNING HORN:
TURN KEY TO “ON” POSITION (ENGINE OFF)

a

b

a -

Small Decal (Transparent)

b -

Larger Decal

7. Test audio warning system during Predelivery Preparation section.

Summary of Contents for 3.0L Carbureted Alpha










































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands