manualshive.com logo in svg

Mercury 3.0L Carbureted Alpha, Installation Manual

Share
Download
Mercury 3.0L Carbureted Alpha Installation Manual Download Page 26

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 26 of 137

90-860172011

5. Install steering assembly as follows:

a. Position steering assembly so that pivot bolts will enter bushings in pivot block or

power steering control valve.

b. Install upper and lower pivot bolts along with tab washers. Ensure that tab washer

tangs straddle the ridge on inner transom plate.

c. Turn pivot bolts all the way in by hand to ensure proper alignment.

d. Ensure steering assembly pivots freely.

6. Torque pivot bolts. Bend tab washer tangs against corresponding flats on bolt heads.

73900

73899

b

c

a

a

c

a -

Tab Washers

b -

Ridge

c -

Pivot Bolts

Description

Nm

lb-in.

lb-ft

Pivot Bolts

34

25

NOTE: It may be necessary to tighten further to align flats on pivot bolt with tangs on tab
washer.

Summary of Contents for 3.0L Carbureted Alpha










































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands