Mercury 3.0L Carbureted Alpha Installation Manual Download Page 56 | Manualshive

Page: 56 / 137

background image

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 56 of 137

90-860172011

Instrumentation Connections

We recommend the use of Quicksilver Instrumentation and Wiring Harnesses. On dual sta-
tion applications, oil pressure and water temperature senders (on engine) must be changed.
Refer to Mercury Precision Parts / Quicksilver Accessories Guide for selection.

The 4 basic gauges that must be used with the engine are:

•

Tachometer

•

Oil Pressure

•

Water Temperature

•

Voltmeter

IMPORTANT: Connect fused accessory panel (40-amp current draw maximum) must
be connected as shown in the wiring diagrams.

1. Route instrumentation wiring harness back to engine, making sure that harness does

not rub or get pinched. If an extension harness is required, be sure to secure connection
properly.

2. Fasten harnesses to boat at least every 18 in. (460 mm), using appropriate fasteners.

3. Place hose clamp over instrumentation wiring harness.

4. Connect the instrumentation wiring harness to engine harness plug at location shown.

74754

a

Typical

a -

Wiring Harness Connector

5. Tighten hose clamp to secure wiring harness to engine harness plug.

«
...
54
55
56
57
58
...
»

Summary of Contents for 3.0L Carbureted Alpha










































































































































Reviews:

No comments

Related manuals for 3.0L Carbureted Alpha

Brand: Indmar Pages: 94

Brand: FAAC Pages: 22

Brand: V2 Pages: 14

3T-MOTORS 3T45-10R

Brand: 3T-Components Pages: 20

Brand: Saito Pages: 2

Brand: Parker Pages: 71

Brand: MTU Pages: 239

Brand: Himax Pages: 2

Brand: Saito Pages: 27

Brand: Mile HaoXianG Model Technology Pages: 3

Brand: EBARA Pages: 36

Brand: Clinton Pages: 23

Brand: Chamberlain Pages: 20

Brand: Clinton Pages: 24

Brand: Wilesco Pages: 4

Brand: Yanmar Pages: 231

Brand: Stober Pages: 6

Brand: O.S. engine Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands