Mercury 3.0L Carbureted Alpha Installation Manual Download Page 89

Page: 89 / 137

GASOLINE STERNDRIVE INSTALLATION MANUAL

90-860172011

Page 89 of 137

Shift Cable Installation

Alpha Models - Drive Unit Installed

IMPORTANT: Shift cable adjustment for a right hand (RH) rotation drive unit is
different than the procedure for adjusting a left hand (LH) rotation drive unit. Be sure
to refer to the appropriate procedure when performing the following steps.

IMPORTANT: Drive unit must be installed.

IMPORTANT: DO NOT run engine.

1. Remove remote control shift cable and shift assist assembly (if installed).

75414

50310

With Shift Assist Assembly Without Shift Assist Assembly

a -

Shift Assist Assembly

b -

Remote Control Shift Cable

2. Ensure shift lever adjustable stud is at bottom of slot.

50309

a -

Adjustable Stud

Summary of Contents for 3.0L Carbureted Alpha










































































































































Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands

Mercury 3.0L Carbureted Alpha, Installation Manual

Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands