Mercury 3.0L Carbureted Alpha Installation Manual Download Page 44

Page: 44 / 137

GASOLINE STERNDRIVE INSTALLATION MANUAL

Page 44 of 137

90-860172011

5. On applications with through the propeller exhaust: Proceed to Step 7.

6. On applications with through the hull or through the transom exhaust:

a. Move load weight to bow to simulate greatest bow-down attitude the boat will

encounter in normal operation.

b. Recheck exhaust system slope.

7. Move load weight and cargo weight to stern of boat to stimulate greatest stern-down

attitude the boat will encounter such as when loading.

IMPORTANT: Be sure to consider swim platform loading and personal watercraft.

8. Recheck exhaust system measurements.

Minimum Exhaust Elbow Height from Top of Elbow to Waterline

Model

Measurement

All V6 and V8

13 in. (330 mm)

77956

70082

13 [330]

a -

Top Of Transom

b -

Highest Point On Exhaust Elbow

c -

Measurement

d -

Waterline

Additional requirements for through the hull or transom exhaust system applications:

Minimum Continuous Downward Slope (Exhaust Hoses, Collector, Etc.)

Model

Measurement (degrees)

All Sterndrive

Summary of Contents for 3.0L Carbureted Alpha










































































































































Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands

Mercury 3.0L Carbureted Alpha, Installation Manual

Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands