manualshive.com logo in svg

Mercury 3.0L Carbureted Alpha, Installation Manual

Share
Download
Mercury 3.0L Carbureted Alpha Installation Manual Download Page 115

GASOLINE STERNDRIVE INSTALLATION MANUAL

90-860172011

Page 115 of 137

3.0L Single Point Drain

CAUTION

Ensure bilge pump is operating before beginning procedures. Excess water in bilge
can damage engine or cause boat to sink.

CAUTION

Allow engine to cool down before disconnecting blue drain hoses. Engine water
temperature can exceed 160

°

 F (71

°

 C).

CAUTION

Do not operate engine with blue drain hoses disconnected. Hot water can discharge
violently.

IMPORTANT: Do NOT start or operate engine at any point in this procedure.

1. Turn on bilge pump.

2. Push quick connect fitting release buttons and remove blue drain hoses from the

bracket.

76242

a

b

a -

Quick Connect Fitting Release button

b -

Blue Drain Hoses

3. Pull T-handle until the hose guide is in contact with the quick connect fittings.

76243

b

a

a -

T-Handle

b -

Hose Guide

Summary of Contents for 3.0L Carbureted Alpha










































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands