Mercury 3.0L Carbureted Alpha Installation Manual Download Page 21

Page: 21 / 137

GASOLINE STERNDRIVE INSTALLATION MANUAL

90-860172011

Page 21 of 137

Installing Inner Transom Plate

1. Insert wires, hoses and shift cable through appropriate openings in inner transom plate.

2. Position gimbal housing on transom and hold in place.

IMPORTANT: Tighten the transom assembly fasteners using an X-pattern torque
sequence, starting from the middle fasteners. Tighten in small increments and go
around the pattern several times until the proper torque is achieved.

3. Secure transom assembly with hardware as shown. Torque the hardware.

Description

lb-in.

lb-ft

Transom Assembly Hardware

4. Attach continuity wires.

IMPORTANT: Steering lever continuity circuit wire must be positioned as shown to
avoid stressing wire when steering lever moves.

71626

71628

70005

71627

71629

a -

Locknuts And Flat Washers (8)

b -

Torque Sequence

c -

Continuity Wire

Summary of Contents for 3.0L Carbureted Alpha










































































































































Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands

Mercury 3.0L Carbureted Alpha, Installation Manual

Search results

Summary of Contents for 3.0L Carbureted Alpha

Reviews:

Related manuals for 3.0L Carbureted Alpha

Brands by name

Popular brands