manualshive.com logo in svg

Mercury 3.0L Carbureted Alpha, Installation Manual

Share
Download
Mercury 3.0L Carbureted Alpha Installation Manual Download Page 65

GASOLINE STERNDRIVE INSTALLATION MANUAL

90-860172011

Page 65 of 137

WARNING

Avoid water leakage into boat. Damage to U-joint bellows could result in water
entering the boat. Do not damage the U-joint bellows when removing a section of
the water hose attached between the gimbal housing and bell housing.

NOTE: Move the trim limit switch wires and speedometer hose to avoid damaging them
when cutting the water hose. The existing tie strap and clip can be reused if they are moved
and repositioned after the hose is cut.

5. Cut completely through the water hose 5 in. (127 mm) in front of the aft end of the hose

where it is fitted into the bell housing. in the area shown. DO NOT damage the U-joint
bellows. Discard loose hose piece.

6. Secure the trim limit switch wires and speedometer hose to the remaining section of

water hose using existing tie strap and clip.

71184

b

c

f

a

e

d

b

c

f

a

e

d

a -

Tie Strap

b -

Clip

c -

Water Inlet Hose

d -

Speedometer Hose

e -

Trim Limit Wire Harness

f -

Cutting Area

Summary of Contents for 3.0L Carbureted Alpha










































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands